668583
16
Zoom out
Zoom in
Previous page
1/93
Next page
16
will be heard during the interval specified
by the TIME knob.
FB: Adjusts the amount of change to the shape
of the LFO waveform.
PITCH SHIFT Shifts the pitch of the input audio upward
or downward.
TIME : Adjusts the delay time.
MOD: Adjusts the pitch of the input audio.
FB: Adjusts the amount of feedback for the
pitch-shifted sound.
DELAY A stereo delay.
TIME: Adjusts the delay time.
MOD: Adjusts the time before reaching the delay
time specified by TIME.
FB: Adjusts the amount of feedback.
TAPE ECHO An effect that simulates a tape echo.
TIME: Adjusts the delay time.
MOD: Adjusts the output level.
FB: Adjusts the amount of feedback.
The display indication when operating the TIME knob
When you operate the TIME knob, the specified TIME parameter is shown
in the display for approximately two seconds. The number shown indi-
cates the beat. For example, a beat of 1/4 (quarter note) is shown as “1.4”
in the display.
Limitations on the delay time
Depending on the combination of the BPM synchronization setting and the
TIME parameter, the TIME parameter of the channel effect may exceed the
allowable range. If this occurs, the display will indicate “FULL,” and the
delay time will be set to the maximum allowable setting.
6. Loop Sampler and Master Effect
The loop sampler and the master effect are connected to the SAMPLER/FX
bus in series.
Input channel selection and mixing
The audio of the mixer channel selected by the CH SELECT switch is sent
to the SAMPLER/FX bus, and will be the input signal for the loop sampler
and master effect.
The MASTER FX & SAMPLE MIX fader will adjust the mix balance be-
tween the sound that has passed through the loop sampler and master
effect, and the sound (“dry” sound) selected by the CH SELECT switch. By
pressing the CUE button, you can monitor the “wet” sound via the CUE
bus even if this is set to the “dry” side.
Loop sampler
This is a loop sampler that lets you play the recorded sample using either
Gate Play or Loop Play methods.
Operating procedure
1. Specify the recording/playback time.
The recording/playback time is specified by the LOOP LENGTH
knob, relative to the BPM.
Use the LOOP LENGTH knob to specify the number of beats that will
be recorded/played-back. For example if you set the LOOP LENGTH
knob to “1/4”, the length will be one quarter-note beat. The duration
of one beat depends on the BPM value. (Refer to the table. Units are
seconds.)
BPM 120 40 60 200 300
1/256 0.008 0.023 0.015 0.005 0.003
1/32 0.625 0.186 0.125 0.375 0.025
1/8 0.25 0.75 0.5 0.15 0.1
1/4 0.5 1.5 1 0.3 0.2
1/1 2641.2 0.8
4/1 824164.8 3.2
2. Using Gate Play and Loop Play.
To sample with Gate Play
When you press the GATE PLAY button, sampling will occur only for
the time specified by the LOOP LENGTH knob.
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Korg Zero 4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Korg Zero 4 in the language / languages: English, German, French as an attachment in your email.

The manual is 3,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info