488479
13
Zoom out
Zoom in
Previous page
1/58
Next page
Installation
Korg 1212 I/O 9
English
Stereo analog input
This input is used to bring analog signals into the 1212 I/O. You can
connect this to the output of a mixer, microphone pre-amp, synthesizer,
and so on. To allow use with a wide range of equipment, the analog input
may be configured for either +4 dBu or -10 dBV signal levels. For more
information, please see “Analog levels: +4 or -10” on page 3.
Microphones and electric guitar outputs should be sent through a mixer or
pre-amp first, to bring them up to +4 or -10 levels; otherwise, their signals
will be too weak.
The analog input uses a 1/4” TRS (tip-ring-sleeve) connector to carry a
stereo, unbalanced signal. The tip carries the right side, the ring carries the
left side, and the sleeve carries the ground. You can use standard “insert”
cables to bring the signals out to a pair of 1/4” mono connectors.
Stereo analog output
This connector is used to bring analog signals out of the 1212 I/O, into
your mixer, amplifier, etc. To allow use with a wide range of equipment, the
analog output may be configured for either +4 dBu or -10 dBV signal levels.
For more information, please see “Analog levels: +4 or -10” on page 3.
As with the analog inputs, described above, the output uses a 1/4” TRS
(tip-ring-sleeve) connector to carry a stereo, unbalanced signal. The tip
carries the right side, the ring carries the left side, and the sleeve carries the
ground. You can use standard “insert” cables to bring the signals out to a
pair of 1/4” mono connectors.
ADAT optical input
The ADAT optical input carries eight channels of digital audio. You can
connect this to the digital output of any multitrack recorder, digital mixer,
effects processor, or other digital audio device which supports the ADAT
optical format.
You can also connect this to the SoundLink DRS 880 A/D Audio Interface,
which will provide the 1212 I/O with eight additional analog inputs.
ADAT optical output
The ADAT optical output carries eight channels of digital audio. You can
connect this to the digital input of any multitrack recorder, digital mixer,
effects processor, or other digital audio device which supports the ADAT
optical format.
You can also connect this to the SoundLink DRS 880 D/A Audio Interface,
which will provide the 1212 I/O with eight additional analog outputs.
S/PDIF breakout connector
This connector should only be used with the special S/PDIF breakout cable
included with the 1212 I/O. This cable has a 4-pin mini-DIN connector at
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Korg SoundLink DRS 1212 I-O at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Korg SoundLink DRS 1212 I-O in the language / languages: English as an attachment in your email.

The manual is 0,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Korg SoundLink DRS 1212 I-O

Korg SoundLink DRS 1212 I-O User Manual - German - 67 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info