668721
13
Zoom out
Zoom in
Previous page
1/94
Next page
7
Front and rear panel
OUTPUT [L/MONO], [R] jacks
Connect your powered monitors,
stereo amp, mixer, or multi-track
recorder to these jacks.
Use the L/MONO jack for monaural
connection.
[PHONES] jack
Connect your headphones
(stereo 1/4" plug) to this jack.
MIDI
Use these connectors to connect external MIDI
devices to the R3 so that MIDI data can be
transferred.
[MIDI IN] connector
This connector receives MIDI data.
[MIDI OUT] connector
This connector transmits MIDI data.
[MIDI THRU] connector
Incoming MIDI data is retransmitted without
change from this connector. Use this when you
want to pass the same stream of MIDI data to
multiple MIDI devices.
[AUDIO INPUT 1] jack
For synthesizer programs, you can connect an external
sequencer, audio device, or 1/4" plug microphone to this
jack, and use the input signal as the oscillator 1
waveform. For vocoder programs, you can use this signal
as the modulator. Use the front panel [AUDIO INPUT 1]
knob and [MIC] switch to control the input level.
If you want to use this jack, you must set the front panel
[MIC] switch to the REAR position. If the [MIC] switch is
set to XLR, the front panel [MIC] jack will be used rather
than this jack.
[MIC/LINE] switch
Set this to the MIC position if you’ve connected a mic to
the AUDIO INPUT 1, or to the LINE position if you’ve
connected an external synthesizer or audio device.
In some cases, noise may occur when you operate
this switch. Turn the [MASTER VOLUME] knob all the
way toward the left before you operate the switch.
[AUDIO INPUT 2] jack
For synthesizer programs, you can
connect an external synthesizer or
audio device to this jack and use its
audio signal as the oscillator 1
waveform.
For vocoder programs, you can use
this signal as the external carrier of the
vocoder. Use the front panel [AUDIO
INPUT 2] knob to control the input
level.
[POWER/STANDBY] switch
Tur ns the power on or off. (p.10)
DC12V IN connector
Connect the included AC adaptor to this
connector. Connect the AC adaptor to the R3
before you plug the adaptor into an AC outlet.
ASSIGNABLE
You can connect a foot switch and foot pedal to these jacks.
[SWITCH] jack
Connect a foot switch or damper pedal to this jack.
[PEDAL] jack
Connect a foot pedal to this jack.
[USB] connector
Connect this to your computer so that MIDI data can
be transferred between the computer and the R3.
This also lets you use the included Editor/Librarian
software to edit the R3’s parameters.
[Contrast knob]
Adjusts the contrast of the main display
and the sub-displays. The readability of
the displays will depend on your viewing
angle, so you should adjust the contrast
as needed for best visibility.
Rear panel
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Korg R3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Korg R3 in the language / languages: English as an attachment in your email.

The manual is 5,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info