668724
24
Zoom out
Zoom in
Previous page
1/450
Next page
20
Overview
Rear Panel
LEFT, RIGHT
Use these line-level outputs to send the final stereo mix to an
external device. Connect either of them to output the signal in
mono. Adjust the output level with the MASTER VOLUME
knob.
Connect two mono cables to these outputs. Connect the other
end of the cables to a stereo channel of your mixer, two mono
channels, two powered monitors, or the CD, LINE IN or TAPE/
AUX input of your audio system. Don’t use the PHONO inputs
of your audio system!
Connecting a jack to these outputs will not deactivates the inte-
grated speakers. This way, you can continue to monitor your
playing, while the signal is sent to the main mixer.
AUDIO IN Section
Use these connectors to connect a
dynamic microphone, another key-
board/synthesizer, or a CD player.
LEFT, RIGHT
Use these connectors to connect a line-level input source, such
as a CD player or a synthesizer, or a dynamic microphone. The
signal routing, and the correct impedence for these inputs, can
be selected with the “Input Routing” parameter in the Global >
Audio & Video > Audio In page (see page 264).
• When the “Input Routing parameter is set toLeft In to Voice
Processor”, you can connect a dynamic microphone to the LEFT
audio input. Use the MIC GAIN knob to adjust the input gain.
Set the volume level of the AUDIO IN signal in the mix by using
the MIC VOLUME knob, while watching at the AUDIO IN LED
on the control panel (see “Mic Setting Section” on page 17).
• When the “Input Routing” parameter is set to “Audio Ins to
Direct Out, you can connect a line-level input source to the
LEFT and RIGHT audio inputs. Use the sources output volume
control to adjust the input level, while watching at the AUDIO
IN LED on the control panel.
MIC GAIN
Use this controls to adjust the input sensitivity of the LEFT con-
nector (from 0 to +40dB) when it is set to the microphone input
sensitivity (see above). You can check the input level by watching
at the AUDIO IN LED on the control panel (see “Mic Setting
Section” on page 17).
Power
This is where you connect Pa900 to the power line.
ACV cable connector
Plug the supplied AC cable into this con-
nector. When the cable is connected, the
instrument is in standby mode. To let it
enter or exit standby, use the STANDBY
switch located on the front panel.
War ning : When the instrument is in standby mode, it is still con-
nected to the power line. Accessing the inside of the instrument can
be dangerous. To completely disconnect the instrument from the
power, unplug the power plug from the power socket on the wall.
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Korg PA900 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Korg PA900 in the language / languages: English as an attachment in your email.

The manual is 44,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info