Manual Konig Electronic SAS-ALARM120 (page 9 of 276) (All languages)

731315

Zoom out

Zoom in

1/276

ENGLISH

on the remote control to arm the alarm and OFF to disarm. The delay time

for entering and leaving the protected area is between 20~25seconds.

7. It’s recommended to test the alarm system for correct operation with rst

use and every 3months.

Procedure:

a) Switch on the alarm unit to ALARM or CHIME (for testing recommend).

b) Push the ON button on the remote control to arm the alarm.

c) Wait for 20~25seconds (delay time).

d) For testing door/window sensor, open every door or window one

by one and check if the corresponding LED lights up and the CHIME

sounds.

e) For testing PIR sensor, move around the PIR sensor and check if the

corresponding LED lights up and the CHIME sounds. Note: the LED

indicator on the PIR sensor lights up also.

f) Disarm the alarm if everything operates correct.

g) The alarm system is ready to use.

Note:

1) The alarm unit will give a conformation tone when armed or disarmed. The

tone for CHIME is dierent as for ALARM.

2) If a sensor does not need to be switched on, it’s possible to switch o every

sensor individually with the on/o switch. In this case the sensor is no part

of the alarm system anymore when armed (except PIR sensor).

3) A sensor switched to RF+ALARM will always give an alarm sound on the

sensor itself, unless the alarm unit is armed or disarmed.

4) When a sensor is triggered and the siren of the alarm unit sounds, it needs

to be switched o with on/o switch of the alarm unit. After that the alarm

unit can be switched on again. When the alarm keeps on going after arming

the system, check if every sensor is installed properly.

Specications:

Alarm unit (gure 1):

• Power: 4.5 V DC (3x battery AA, not included)

• Standby current: <1.5mA

• Chime current: <90mA

• Alarm current: <130mA

• Alarm volume: 100 dB (0.5m)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Konig Electronic SAS-ALARM120 in the language / languages: All languages as an attachment in your email.

The manual is 5,96 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Konig Electronic SAS-ALARM120 Manual

Product: