731315

Konig Electronic SAS-ALARM120 Manual

7
Zoom out
Zoom in
Previous page
1/276
Next page
ENGLISH
7
The slightest vibration will trigger the sensor. It’s not recommended to
install the vibrate sensor on windows near to doors. Slamming doors will
trigger the sensor.
4. Insert, according the diagram inside the battery compartment, (backside)
the batteries for PIR sensor (3x AAA). The PIR sensor needs to warm up for
30~40seconds for rst use. In this period it cannot detect motion. Install
the PIR sensor at a height of 1~1.5m for best performance. Do not install
the PIR sensor into direct sunlight, facing towards windows, objects that
move easily and heat or cold source.
5. Remove the transparent front cover of the alarm unit to write down the
position of the sensors corresponding with the numbered LED. (e.g. sensor
1=front door, 2=kitchen window, etc.).
6. Install the alarm unit to a location. The distance between the alarm unit and
the most far away sensor may not exceed 60m (open area)*.
7. Switch on the alarm unit to ALARM or CHIME function. If switched to
CHIME, the alarm unit will sound like a door bell when a door or window is
opened. Switched to ALARM generates a 100dB loud siren. When the alarm
unit is switched on, the alarm is not armed (active) yet. Push the ON button
on the remote control to arm the alarm and OFF to disarm. The delay time
for entering and leaving the protected area is between 20~25seconds.
8. It’s recommended to test the alarm system for correct operation with rst
use and every 3months.
Procedure:
a) Switch on the alarm unit to ALARM or CHIME (for testing recommend).
b) Push the ON button on the remote control to arm the alarm.
c) Wait for 20~25seconds (delay time).
d) For testing door/window sensor, open every door or window one
by one and check if the corresponding LED lights up and the CHIME
sounds.
e) For testing PIR sensor, move around the PIR sensor and check if the
corresponding LED lights up and the CHIME sounds. Note: the LED
indicator on the PIR sensor lights up also.
f) For testing vibrate sensor, hit carefully on the window and check if the
corresponding LED lights up and the CHIME sounds.
g) Disarm the alarm if everything operates correct.
h) The alarm system is ready to use.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Konig Electronic SAS-ALARM120 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Konig Electronic SAS-ALARM120 in the language / languages: All languages as an attachment in your email.

The manual is 5,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info