780521
19
Zoom out
Zoom in
Previous page
1/44
Next page
KONA OWNER’S MANUAL
20
(3) On a derailleur gear system, pull the derailleur body
back with your right hand.
(4) With a cam action mechanism, move the quick-release
lever to the OPEN position (g. 8b). With a through bolt
or bolt on mechanism, loosen the fastener(s) with an ap-
propriate wrench, lock lever or integral lever; then push
the wheel forward far enough to be able to remove the
chain from the rear sprocket.
(5) Lift the rear wheel off the ground a few inches and
remove it from the rear dropouts.
d. Installing a disk brake or rim brake Rear Wheel
CAUTION: If your bike is equipped with a rear disk
brake, be careful not to damage the disk, caliper or
brake pads when re-inserting the disk into the caliper.
Never activate a disk brake’s control lever unless the
disk is correctly inserted in the caliper.
(1) With a cam action system, move the cam lever to the
OPEN position (see g. 8 a & b). The lever should be on
the side of the wheel opposite the derailleur and free-
wheel sprockets.
(2) On a derailleur bike, make sure that the rear derail-
leur is still in its outermost, high gear, position; then pull
the derailleur body back with your right hand. Put the
chain on top of the smallest freewheel sprocket.
(3) On single-speed, remove the chain from the front
sprocket, so that you have plenty of slack in the chain.
Put the chain on the rear wheel sprocket.
(4) Then, insert the wheel into the frame dropouts and
pull it all the way in to the dropouts.
(5) On a single speed or an internal gear hub, replace
the chain on the chainring; pull the wheel back in the
dropouts so that it is straight in the frame and the chain
has about 1/4 inches of up-and-down play.
(6) With a cam action system, move the cam lever
upwards and swing it into the CLOSED position (g. 8 a
& b). The lever should now be parallel to the seat stay or
chain stay and curved toward the wheel. To apply enough
clamping force, you should have to wrap your ngers
around the fork blade for leverage, and the lever should
leave a clear imprint in the palm of your hand.
(7) With a through-bolt or bolt-on system, tighten the
fasteners to the torque specications in the hub manufac-
turer’s instructions.
NOTE: If, on a traditional cam action system, the lever
cannot be pushed all the way to a position parallel to
the seat stay or chain stay, return the lever to the OPEN
position. Then turn the tension adjusting nut counter-
clockwise one-quarter turn and try tightening the lever
again.
WARNING: Securely clamping the wheel with a
cam action retention device takes considerable force.
If you can fully close the cam lever without wrapping
your ngers around the seat stay or chain stay for
leverage, the lever does not leave a clear imprint
in the palm of your hand, and the serrations on the
wheel fastener do not emboss the surfaces of the
dropouts, the tension is insufcient. Open the lever;
turn the tension adjusting nut clockwise a quarter
turn; then try again. See also the rst WARNING in
this Section, p. 16.
(8) If you disengaged the brake quick-release mechanism
in 3. c. (2) above, re-engage it to restore correct brake
pad-to-rim clearance.
19
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kona 2020 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kona 2020 in the language / languages: English as an attachment in your email.

The manual is 1.51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info