780524
16
Zoom out
Zoom in
Previous page
1/42
Next page
KONA OWNER’S MANUAL
Your bicycle may be equipped with a different securing
method for the front wheel than for the rear wheel.
Discuss the wheel securing method for your bicycle with
your dealer.
It is very important that you understand the type of
wheel securing method on your bicycle, that you know
how to secure the wheels correctly, and that you know
how to apply the correct clamping force that safely
secures the wheel. Ask your dealer to instruct you in
correct wheel removal and installation, and ask him to
give you any available manufacturer’s instructions.
WARNING: Riding with an improperly secured
wheel can allow the wheel to wobble or fall off the
bicycle, which can cause serious injury or death.
Therefore, it is essential that you:
1. Ask your dealer to help you make sure you know
how to install and remove your wheels safely.
2. Understand and apply the correct technique for
clamping your wheel in place.
3. Each time, before you ride the bike, check that the
wheel is securely clamped.
The clamping action of a correctly secured wheel must
emboss the surfaces of the dropouts.
1. Front Wheel Secondary Retention Devices
Most bicycles have front forks which utilize a secondary
wheel retention device to reduce the risk of the wheel
disengaging from the fork if the wheel is incorrectly
secured. Secondary retention devices are not a substitute
for correctly securing your front wheel.
Secondary retention devices fall into two basic categories:
a. The clip-on type is a part which the manufacturer adds
to the front wheel hub or front fork.
b. The integral type is molded, cast or machined into the
outer faces of the front fork dropouts.
Ask your dealer to explain the particular secondary reten-
tion device on your bike.
WARNING: Do not remove or disable the secondary
retention device. As its name implies, it serves as a
back-up for a critical adjustment. If the wheel is not
secured correctly, the secondary retention device can
reduce the risk of the wheel disengaging from the fork.
Removing or disabling the secondary retention device
may also void the warranty. Secondary retention
devices are not a substitute for correctly securing your
wheel. Failure to properly secure the wheel can cause
the wheel to wobble or disengage, which could cause
you to lose control and fall, resulting in serious injury
or death.
2. Wheels with cam action systems
There are currently two types of over-center cam wheel
retention mechanisms: the traditional over-center cam
(g. 8a) and the cam-and-cup system (g. 8b). Both use
an over-center cam action to clamp the bike’s wheel
in place. Your bicycle may have a cam-and-cup front
wheel retention system and a traditional rear wheel cam
action system.
a. Adjusting the traditional cam action mechanism (g. 8a)
The wheel hub is clamped in place by the force of the
over-center cam pushing against one dropout and
pulling the tension adjusting nut, by way of the skewer,
against the other dropout. The amount of clamping force
is controlled by the tension adjusting nut. Turning the
tension adjusting nut clockwise while keeping the cam
lever from rotating increases clamping force; turning
it counterclockwise while keeping the cam lever from
16
2K17_Kona_Owners_Manual.indd 16 29.1.2016 15.27
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kona 2017 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kona 2017 in the language / languages: English as an attachment in your email.

The manual is 1.8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info