Manual Koenic KDW 6041 D FI (page 23 of 98) (English, German, Dutch, French, Italian, Spanish)

782817

Zoom out

Zoom in

1/98

English

Installation

Fig. 1The dishwasher must be installed in

sucient proximity of a suitable water,

sewage and electrical connection.

Caution

After unpacking open the door and remove

all transport protections from the baskets

and spray arms. Ensure that the spray arms

can rotate freely.

Note:

Please check the included mounting material,

brackets, screws and Velcro strip for attaching

the decorative panel, etc.

1Observe the installation dimensions.

• A location near the sink is recommended

to allow for an easier connection of

the dishwasher to water and sewage

connections

• At the back of one or both lateral

cupboards, recesses of size 80 x 100 mm

must be ﬁtted for water, sewage and

electrical connection (A).

If the dishwasher is installed in a corner, a

minimum clearance of 50 mm between the

opened door and surrounding cabinets must

be respected.

Note the dimensions, holes and cutouts of

the decorative plate.

2Fasten the condensation strip below the

worktop. Make sure that it closes with the

front edge of the countertop.

3Make sure that the power cord and the

water inlet and outlet are not under tension

and that they are not bent. Make sure that

the water connection is properly sealed and

tightened to prevent leakage.

4Lay the drain hose without pulling and

kinking. Do not force the dishwasher under

the worktop, move it only by hand.

5Place the dishwasher in its ﬁnal position.

The dishwasher must be placed in an

absolutely level installation position.

• The rear stands can be adjusted in height

by turning the middle Phillips screw

(Pos.A). Please refer to the ﬁgure next to

the screw (UP: rear is raised, DOWN: rear

is lowered).

• The front feet can be adjusted by turning

them by hand.

• Check the horizontal stand with a spirit

level on horizontal or vertical surfaces in

the interior of the dishwasher and the

door.

6Make sure that the dishwasher is placed

levelled and does not tilt.

7Mark the holes for the retaining plates and

sleeves on the decorative plate and pre-drill.

8Fix the sleeves at the top and the retaining

plates at the bottom of the decor panel.

9Now place the decor panel on the matching

recesses on the door and attach it to the

door of the dishwasher.

10 Remove the 4 screws inside of the door.

Screw the supplied 4 long screws through

the door and fasten the decorative plate.

11 The springs of the dishwasher door were

pre-set at the factory.

• After installation of the decorative plate,

the spring force of the door may have to

be adjusted.

• Twist the adjusting screws on both sides

to increase/decrease the spring force.

Please refer to the illustration next to

the screws.

• The spring force is adjusted correctly

when the fully opened door remains in a

horizontal position and can be moved up

all the way by slightly pulling on it.

IM_KDW 6041 D FI_6L_201119_V06_HR.indb 23IM_KDW 6041 D FI_6L_201119_V06_HR.indb 23 18/11/2020 6:28 PM18/11/2020 6:28 PM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Koenic KDW 6041 D FI in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 21.62 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Koenic KDW 6041 D FI Manual

Product: