212562
37
Zoom out
Zoom in
Previous page
1/70
Next page
A-61167 April 2005 33
Problem solving Occasionally, you may experience a problem with your scanner. In many
cases, you can easily fix the problem yourself. To perform suggested
maintenance, refer to the Maintenance section. You may also need to
check your scanning application.
Problem Possible Solution
The scanner will not scan/
feed documents
Make sure that:
the power cord is plugged in and the power is on.
the scanner and printer access doors are completely closed.
the proper power-up sequence was followed, the scanner’s green light is on,
and the software has enabled scanning.
documents are making contact with the feed module.
the height of batched documents is less than 10.2 mm (0.4 in.) or
approximately 150 sheets of 60 g (16 lb.) paper.
documents meet specifications for size, weight, and type, etc.
for thicker documents, you lift the gap release button during feeding.
you check the feed module and separator module for signs of wear, and
replace these parts if necessary.
the imaging guides are securely in place and pushed all the way in.
You can also power the scanner down and power up again or follow the
instructions in “System is not responding” in this section.
Calibration has failed Make sure that:
the lamps have been on at least three minutes.
you are using a proper calibration target. Use the 29.7 cm (11.7 in.) square
calibration target (CAT No. 131 7304) that is included with your scanner.
the transport area is clear of obstructions.
Documents are jamming Make sure that:
the output tray and guides are adjusted for the length of documents
being scanned.
all jammed documents have been removed from the paper transport area.
documents meet specifications for size, weight, and type, etc.
all staples and paper clips have been removed from the documents.
the separator module and feed module are clean and properly installed.
the drive rollers are clean.
the imaging guides are clean.
“False” paper jams
are occurring
Make sure that the paper transport area is clean.
If you are scanning documents that contain holes (e.g., 3-hole punch paper),
rotate the documents and rescan.
NOTE: If you are using an i280 Scanner, use Special Document mode to scan
documents containing holes.
35.6 cm (14 in.) or longer
documents are not feeding or
are jamming
Make sure that the input and output tray extenders are pulled out to provide
support for long documents.
Jam error appears
when scanning with
Long Paper mode
Change the scanning resolution to 300 dpi or less and scan the document again.
37


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kodak i250 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kodak i250 in the language / languages: English as an attachment in your email.

The manual is 2,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info