212562
38
Zoom out
Zoom in
Previous page
1/70
Next page
34 A-61167 April 2005
Problem Possible Solution
Image quality is poor or
has decreased
Make sure that:
the scanner is clean. Refer to the Maintenance section.
the scanner is calibrated. Refer to the Maintenance section.
The lamps shut off too soon The lamps in the i200 Series Scanners will turn off after 5 minutes of no scanner
activity. If the lamps are off, but the scanner has not yet gone into the Energy Star
mode (default 15 minutes), there will be a delay of about 5 seconds for the lamps
to warm up again.
The default setting for the Energy Star is 15 minutes, and if not changed to
another value between 16 and 60 minutes, the lamps will turn off after
5 minutes of no scanner activity, followed 10 minutes later by the fan turning
off (15 minutes total).
If you set the Energy Star timeout to a new value greater than 15 minutes, you
must scan at least one document for that setting to be enabled. After this setting
has been enabled, it will be enforced until a new setting is selected or the
scanner is powered off and back on.
Documents are skewed
during scanning
Make sure that:
the document side guides are adjusted to fit the documents being fed.
documents are being fed perpendicular to the feed module.
documents are being fed in the center of the ADF.
all staples and paper clips have been removed from the documents.
the feed module, separator module, and drive rollers are clean.
Scanner pauses excessively
during scanning
Make sure that:
the host computer meets minimum requirements for scanning.
there is enough free space on the hard disk drive.
all other applications are closed.
the scanner has the correct amount of memory installed for the documents
being scanned.
You can also try changing the scanning options (compression, etc.) in your
scanning software.
Documents are multifeeding Make sure that:
the leading edges of all batched documents are centered in the ADF so that
each document will come in contact with the feed rollers.
the feed module and separator module are clean and not worn.
documents with an unusual texture or surface are fed manually.
Roller marks or streaks appear
on documents after scanning
Clean the feed module and separator module tires and the drive rollers. Refer to
the Maintenance section.
Vertical lines appear on
the image
Clean the imaging guides. Refer to the Maintenance section.
Calibrate the scanner. Refer to the Maintenance section.
38


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kodak i250 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kodak i250 in the language / languages: English as an attachment in your email.

The manual is 2,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info