212708
98
Zoom out
Zoom in
Previous page
1/108
Next page
6-6 A-61555 April 2009
Messages ID# Operator Message
Clean upper imaging guide 293, 304 The upper imaging guide is dirty or there may be a small piece of
paper in the imaging guide area.
Clean the imaging guides. See Chapter 5, Maintenance for
procedures.
Document count exceeded
maximum value
124 The document counter is larger than the maximum configured
value.
Reconfigure the scanner to allow a larger value for the
document counter. Refeed the document set.
Document too dark to deskew 143 Informational message. The scanner was unable to find the
document edges to determine the skew angle. A full-width, non-
deskewed image has been created.
The document is too dark.
The image is too large.
Rescan using a fixed-sized cropping window.
Document too long 35, 36, 183 A document was measured which exceeded the configured
maximum allowable length. This may be due to a document
overlap.
Check the host monitor to see if there are any overlapped
documents that may need to be rescanned.
This condition may also be caused by poor document
separation.
Replace the separation roller tires and pre-separation pad.
See Chapter 5, Maintenance for procedures.
Front calibration failed 110 The front imaging path calibration failed.
Clean the imaging guides. See Chapter 5, Maintenance for
procedures.
Try to calibrate the scanner again. Be sure you are using the
correct calibration target. See Chapter 3, “Calibrating the
Scanner”.
If the problem persists, call Service.
Front calibration succeeded 111 Informational message. The front image path has been
successfully calibrated.
Image address overflow 120 One of the image address fields is not large enough for the next
image address (i.e., level 2 field width is 2, but the next level 2
value is 100).
Define the image address field to be wider.
Image calibration is suggested 109 Calibrate the scanner when the current batch of documents
has completed.
Image outside document area 177 Based on relative cropping parameters, the image to be
generated from this document would be outside the document
area.
Make sure the relative cropping offset, width and length are
correct and that the correct document is being scanned.
Ink cartridge not installed 282 An attempt was made to use the Enhanced Printer without a ink
cartridge installed.
Be sure the cable is properly connected to the printer carrier
and the ink cartridge is installed in the printer carrier. See
Chapter 4, The Enhanced Printer and Patch Readers for more
information.
NOTE:The ink cartridge must be installed before turning on the
scanner.
98


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kodak i1860 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kodak i1860 in the language / languages: English as an attachment in your email.

The manual is 2,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kodak i1860

Kodak i1860 User Manual - Dutch - 112 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info