212708
100
Zoom out
Zoom in
Previous page
1/108
Next page
6-8 A-61555 April 2009
Messages ID# Operator Message
Paused waiting for host 1, 48 The feeder has stopped and the transport is still running
because the scanner’s internal image buffer is almost full.
Processing will automatically resume after the capture software
application has successfully retrieved enough images to allow
the scanner to continue.
Be sure your host computer meets the recommended
specifications to avoid this condition.
Please update firmware before
scanning
91 The expected production version of operational firmware was
not found. The back-up firmware is in use.
Reload the most recent version of operational scanner
firmware.
Pod door closed 26 Informational message. The pod was closed.
Pod door opened 25 Informational message. The pod is not closed completely.
Power on self-test completed 20 Informational message. The scanner has completed its self-tests
after power-on.
Power on self-test failed 6 This error could occur during scanner power-up.
Power-down the scanner, then power down the PC. Wait a few
seconds and then power the PC back up, then power up the
scanner.
If the problem persists, call Service.
Printer bitmap font in use 281 Informational message. An alternate printer font file was found
and is being used instead of the default font.
Rear calibration failed 112 The rear imaging path calibration failed.
Clean the imaging guides. See Chapter 5, Maintenance for
procedures.
Try to calibrate the scanner again. Be sure you are using the
correct calibration target. See Chapter 3, “Calibrating the
Scanner”.
If the problem persists, call Service.
Rear calibration succeeded 113 Informational message. The rear image path has been
successfully calibrated.
Refeed document set Many ID
numbers
Documents passed through the transport but no images were
created.
Clean document sensors.
Make sure the leading edges of the documents are aligned.
See Chapter 3, “Document preparation” for more information.
Check the condition of your feed module and separation roller
tires and your pre-separation pad. Clean and replace if
necessary.
Refeed these documents and verify that the images have been
captured.
Requested pages scanned 337 Informational message. The scanner has completed scanning
the requested number of documents.
Paused for image processing 63 Informational message. Scanner paused.
Slow host PC may not be able to keep up with the scanner.
Transport timeout 336 Informational message. The transport was turned off due to
inactivity.
100


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kodak i1860 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kodak i1860 in the language / languages: English as an attachment in your email.

The manual is 2,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kodak i1860

Kodak i1860 User Manual - Dutch - 112 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info