212709
99
Zoom out
Zoom in
Previous page
1/108
Next page
A-61555 April 2009 6-7
Messages ID# Operator Message
Input elevator too full, feed module
missing or broken
297 There is too much paper in the input elevator and it is holding
the feed module up. The maximum input elevator capacity is
500 sheets. Remove some documents from the input elevator.
The feed module is not installed properly. See Chapter 5,
Maintenance, for correct installation procedures.
If the problem persists, call Service.
Invalid job setup 4 The image processing values sent by the host are invalid or in
conflict with one another.
Check the job settings for illegal combinations. Refer to the
Image Processing Guide for valid values.
Jam in transport 30 A document is lodged in the transport.
Remove the documents that have been scanned from the
output tray.
Open the pod.
Remove any jammed documents from inside the transport.
Close the pod.
NOTE: The following procedure is a general guideline. Your
procedure may be different depending on how your
application is set up.
Verify the last document that was scanned correctly.
Place any documents that were not scanned at the top of the
batch.
Place the documents in the input elevator and begin scanning.
One or more documents that passed through the transport were
not scanned.
Refeed all documents for which images were not obtained.
Lamps not ready for calibration 107 Calibration was attempted before the lamps were warmed up.
Wait until the lamps have completely warmed (90 seconds)
and try the calibration again.
Lamps not ready for scanning 359, 19 Scanning was attempted before the lamps were warmed up.
Wait for the message Lamps ready for scanning to be
displayed and scan again.
Lamps ready for calibration 108 Informational message. The lamps are warmed and a calibration
can be performed now, if needed. This does not indicate that a
calibrate is needed.
Lamps ready for scanning 280 Informational message. The lamps are warmed and scanning
can be initiated.
Lamps timed out 355 Informational message. The lamps were turned off due to
inactivity.
No paper input elevator 46 The scanner was started with an empty input elevator or the
portion of the document that is covering the paper present
sensor is too dark (the back side of the bottom page).
Place the documents you want to scan in the input elevator
and try again.
Offset the document until the paper present sensor detects it.
99


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kodak i1840 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kodak i1840 in the language / languages: English as an attachment in your email.

The manual is 2,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kodak i1840

Kodak i1840 User Manual - Dutch - 112 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info