212709
97
Zoom out
Zoom in
Previous page
1/108
Next page
A-61555 April 2009 6-5
Message listing Following is an alphabetic list of messages and corrective actions you
can take if one of the following messages is encountered.
Messages ID# Operator Message
Background accessory changed
while powered up
381 The Background Accessory was changed while the scanner was
powered on.
Turn the power off to the scanner, wait a few seconds and
power the scanner back on.
If you get this message and you did not change the
Background Accessory, clean the scanner.
Cable unplugged 319 Some device on the FireWire bus was unplugged/plugged in.
Check that all FireWire connectors are securely fastened.
Calibration failed 106, 331 Clean the imaging guides. See Chapter 5, Maintenance for
procedures.
Try to calibrate the scanner again. Be sure you are using the
correct calibration target. See Chapter 3, “Calibrating the
scanner”.
The calibration target is too small. A 12- x 12-inch calibration
target is required for image calibration.
Calibration target is too narrow.
If the problem persists, call Service.
Calibration succeeded 105, 342 Informational message. The scanner has been successfully
calibrated.
Call Service Many ID
numbers
A condition was detected that may require repair.
Turn the power off to the scanner, wait a few seconds and
power the scanner back on.
If the problem persists, call Service and provide the ID number
of the error.
Cannot calibrate with white
background
184 Both a front and rear print head is installed in the scanner. Only
one print head can be installed at one time.
Remove one of the print heads.
Cannot run with both printers
installed
90 The White Background Accessory is installed in the scanner
while the scanner is trying the calibrate.
Remove the White Background Accessory before calibrating
the scanner.
Check document preparation 123, 135,
81
The gap between your documents is too small.
Make sure the leading edges of the documents are aligned.
See Chapter 3, “Document preparation” for more information.
Check the condition of your feed module and separation roller
tires and your pre-separation pad. Clean and replace if
necessary.
Check imaging guides and lamps 149, 178,
139
Verify that the imaging guides are installed correctly. See
Chapter 5, Maintenance.
Clean both sides of the imaging guides and lower glass plate
between the lamps.
Check that the white patch on the imaging guides is clean and
in good condition.
If the problem persists, call Service.
Clean lower imaging guide 294 The lower imaging guide is dirty or there may be a small piece of
paper in the imaging guide area.
Clean the imaging guides. See Chapter 5, Maintenance for
procedures.
97


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kodak i1840 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kodak i1840 in the language / languages: English as an attachment in your email.

The manual is 2,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kodak i1840

Kodak i1840 User Manual - Dutch - 112 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info