Manual Klarstein 10033257 Icetender (page 18 of 56) (English, German, French, Italian, Spanish)

753570

Zoom out

Zoom in

1/56

GETTING STARTED

1 Take all components out of the packaging.

2 Position the ice maker on a well ventilated place and leave at least 150 mm

distance between the ice maker and the wall. Adjust the feet of the ice maker so that

it is positioned levelly.

3 Connect one end of the exible Φ14 plastic corrugated pipe (supplied with the

machine) with the water outlet tube on the back of the machine, another pipe end

should be placed in a container for surplus water (prepared by the user himself) or

in the sewer.

4 Connect one end of the water inlet tube (supplied with the machine) with the 3/4

inch screw type connector of the water tap so as to get the drinkable tap water. The

water pressure of the water supply pipe is 1-8 kg/cm2.) The other end of the water

inlet tube should be connected with the screw type connector of the water valve on

the back of the ice maker. Be sure to put the gaskets (supplied with the machine)

into both ends of the water inlet tube before connecting. If it is an ice maker for

puried water, a Φ14 corrugated pipe (supplied with the machine) should be used.

Connect one end of the pipe with the puried water supplier (cold water tap or end

of the water drainage tube of a water dispenser) and another end with the water

valve connector on the back of the ice maker. Make sure that the puried water

outlet position is higher than the top of the ice maker.

Note: Wait at least 12 hours after setting up the ice machine for the rst time before

using it for the rst time.

OPERATION

1 Plug the power plug of the appliance into the wall outlet. Then press the power

button on the ice machine to start it - the green “run” light will be lit . The "RUN"

indicator light illuminates. The appliance starts operation. All procedures such as

water inlet, ice making, ice dropping and ice storage are automatically controlled

during ice production. If problems occur, the corresponding indicator lights

illuminate (see indicator lights in the "Troubleshooting" section).

2 Only puried drinking water should be used for the appliance. If the "WATER LOW"

indicator light illuminates and no ice is produced, maybe there is air in the water

inlet tube. Disconnect one end of the water inlet tube from the water valve of the ice

cube maker. Open the water inlet switch until water and air run out from the end.

Then quickly reconnect the water inlet tube with the water valve of the appliance.

Note: If the water storage is defective or the water supply system is faulty, the ice

maker will restart automatically in 24 hours. If the problem has not been solved, stop

the appliance and restart it again.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Klarstein 10033257 Icetender in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 1,25 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Klarstein 10033257 Icetender Manual

Product: