581385

KitchenAid 730-0826 Manual

23
Zoom out
Zoom in
Previous page
1/37
Next page
Check and Adjust the Burners
The burners are tested and factory-set for most efficient operation.
However, variations in gas supply and other conditions may make
minor adjustments to air shutter or low flame setting necessary.
It is recommended that a qualified person make burner
adjustments.
Checking and adjusting the grill burner flames requires removing
the grates and flame tamers.
6. If flame is yellow (not enough air), turn air shutter
adjustment screw counterclockwise. If flame is noisy or lifts
away from burner (too much air), turn air shutter adjustment
screw clockwise.
Adjustment should be made clockwise or counter
clockwise from 1/8” (3.2 mm) to ¼” (6.4 mm).
7. Replace gas burner, sear plates and grates.
8. Light grill using information in the “Outdoor Grill Use”
section. See “Burner Flame Characteristics
A. Air shutter adjustment screw
A
If flame goes out on the “LOW” setting, the low flame setting
must be adjusted.
1. Turn off the valve, and wait until the grill and burners have
cooled down.
2. Remove grill grates and flame tamers.
3. Light grill using information in the “Outdoor Grill Use”
section.
4. Turn burner to its lowest setting.
5. Remove each control knob for the main burners and side
burner by loosening the setscrew with the hex key.
The flames of the grill burners and side burners (on some models)
should be blue and stable with no excessive noise or lifting (LP
gas flames will have a slightly yellow tip). A yellow flame indicates
not enough air. If flame is noisy or lifts away from the burner,
there is too much air. Some yellow tips on flames when the burner
is set to HIGH setting are acceptable as long as no carbon or soot
deposits appear. The flames should be approximately 1" (2.5 cm)
high.
Burner Flame Characteristics
Low Flame Adjustment
Check that burners are not blocked by dirt, debris, insect
nests, etc., and clean as necessary. If they are clean, adjust
air shutters as needed.
IMPORTANT: Before adjusting air shutters, let the burners
cool down completely.
To Adjust:
burner by loosening the setscrew with the hex key.
6. Hold valve stem with pliers and insert a small flat-blade
screwdriver into the shaft.
7. Watch the flame and slowly turn the screwdriver
counterclockwise.
8. Adjust flame to minimum stable flame.
A. Valve stem
B. Small flat-blade screwdriver
C. Pliers
A
B
C
9. Replace the control knob and turn off the burner.
10. Repeat steps 3 through 9 for each burner if needed.
11. Replace the flame tamers and grates after the burners
have cooled.
To Adjust:
1. Light grill using information in the “Outdoor Grill Use” section.
2. Observe flame to determine which burners need adjustment
and how the flame is acting.
3. Turn off the valve and wait until grill and burners have cooled
completely.
4. Remove grill grates and flame tamers.
5. Remove the 1 screw and cotter pin that hold the burner in
place. Remove gas burner from the grill.
A
B
A. Screw
B. Cotter Clip
23
… 23 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for KitchenAid 730-0826 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of KitchenAid 730-0826 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 2,88 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info