483676

Kinzo 71775 Manual

7
Zoom out
Zoom in
Previous page
1/52
Next page
7
A
3-1. Switch lock
The switch trigger can be locked in the center position. (See Fig. 5)
This helps to reduce the possibility of accidental starting when not in use.
To lock the switch trigger, place the Direction of rotation selector in the center position.
3-2. Direction of rotation is controlled by the direction of rotation selector (3)
located above the switch trigger.
To select forward rotation, release the on/off switch and push the forward/reverse lever to Left side of the
tool. To select reverse rotation, push the lever to right side of the tool. When the selector is in center position,
the switch trigger is locked. (See Fig. 5)
3-3. Variable speed
This tool has a variable speed switch that delivers higher speed and torque with increased trigger pressure.
Speed is controlled by the amount of switch trigger depression.
4. Installing and Removing a Bit and a Drill (Fig. 6)
1. Hold ring A of the drill chuck tight with one hand.
2. Turn upper ring B anticlockwise with the other hand until
the drill chuck opening is large enough to accept the tool.
3. Insert the drill or the screwdriver bit into the drill chuck.
4. Turn ring B clockwise until the tool is clamped tightly.
Remove the tool in the opposite way.
5. Adjusting the torque
The torque is adjusted by rotating the torque setting (2),
the torque is greater when the torque setting is set on a higher posi-
tion. The torque is less when the torque setting is set on a low position
“1”denote lowest and “ ” denote highest.Torque is set by means of a torque setting according to diff erent
screw and diff erent material, you can adjust suitable torque, if the screw is long and material is hard,
you can adjust the bigger setting.
6. Drilling
Before use for drilling, the torque setting should be set on drill position “ ”.
When drilling hard smooth surface, use a center punch to mark the desired hole location. This will prevent
the drill bit from slipping off center as the hole is started. Hold the tool fi rmly and place the tip of the drill
or bit into the work piece, applying only enough pressure to keep the bit cutting. Do not force or apply side
pressure to elongate a hole.
7. Wood Drilling
For maximum performance, use high speed steel drills for wood drilling, turn the torque setting on the drill
position“ ”. Begin drilling at a very low speed to prevent the bit from slipping off the starting point. Increase
the speed as the drill bit bites into the material. When drilling through holes, place a block or wood behind
the work piece to prevent ragged or edges on the back side of the hole.
8. Metal drilling
For maximum performance, use high steel bits for metal or steel drilling. Turn the torque setting on the drill
position“ ”. Begin drilling at a very low speed to prevent the bit from slipping off the starting point. Maintain
a speed and pressure which allows cutting without overheating the bit. Applying too much pressure will
overheat the drill, wear the bearings, bend or burn bits, produce off -center or irregular shaped holes.
When drilling large holes in metal, it is recommended that you drill with a small bit at fi rst, then fi nish with a
large bit, also lubricate the bit with oil to improve drilling action and increase bit life.
9. Disposal of an exhausted battery
To preserve natural resources place recycle or dispose of the battery properly.
This product contains Ni-Cd batteries. Consult your local waste authority for information regarding available
recycling and /or disposal options.
AB
Fig. 6
71775 Manual.indd 7 31-12-10 15:35
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kinzo 71775 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kinzo 71775 in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 5,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info