635287

Kettler Verso TX1 - 7882-099 Manual

30
Zoom out
Zoom in
Previous page
1/42
Next page
Owner’s Manual
29
adjustment on any treadmill. To eliminate this slipping, tension both Allen bolts on the rear roller
1/4 turn. Try the treadmill again to check for slipping. Repeat if necessary, but NEVER turn
the roller bolts more than 1/4 turn at a time.
DRIVE BELT TENSIONING ADJUSTMENT:
If you have tensioned the running belt and are still experiencing a slipping sensation, call your
dealer. Only an authorized dealer should perform tensioning of the drive belt.
LUBRICATING THE DECK:
A well-lubricated deck will ensure high performance of your treadmill and reduce the level of
normal wear and tear to important components. This treadmill has been pre-lubricated at the
factory. However, for optimal performance, the running deck may require periodic lubrication.
With average usage (30 minute workout at 5-6 Km/H 3 times a week for two people) lubricate
every six months. You may adjust the timing of the lubrication based on the intensity of the
treadmill use level.
To check the lubrication level, simply lift the running belt, and put your hand as far into the center
of the belt as you can reach. If your hand shows signs of silicone, then it does not need
additional lubrication. If the board feels dry and there is very little evidence of silicone on your
hand, then additional lubrication is necessary.
TO LUBRICATE THE DECK:
1. Stop running belt so that the seam is located on top and in the center of the deck.
2. Insert extending tube nozzle into spray head of lubricant can.
3. Lift running belt.
4. Position nozzle between the belt and the deck board approximately 200mm (8”) from the front
of the treadmill.
5. Apply the silicon from the front to the rear of the treadmill on each side of the treadmill. Try to
reach the spray as far into the center of the running deck as possible. A light coating of
silicone spray should be applied to the deck under the belt on each side. Be certain the
center of the walking area gets lubricated.
6. Spread the silicon by running the treadmill at 1 Km/H and step gently on the belt from left to
right. Do that for a few minutes and allow the silicon to soak into the belt.
… 30 …


Need help? Post your question in this forum.

Forumrules
1

Forum

kettler-verso-tx1---7882-099

Reset search

  • I have a Kettler tx1 and it’s stuck on error code 4, how do I resolve this issue? Please Submitted on 3-5-2018 at 09:58

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kettler Verso TX1 - 7882-099 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kettler Verso TX1 - 7882-099 in the language / languages: English as an attachment in your email.

The manual is 1,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info