772982
47
Zoom out
Zoom in
Previous page
1/82
Next page
MY20K10-02_1.0_10.11.2020 47
Operation
6.14 Display
6.14.1 Attaching the display
1Place the screen at a 90° angle to the mount on
the handlebars.
2Turn clockwise.
The display is fully attached when it is upright
and locked into position.
6.14.2 Removing the display
The system – the display and drive system –
should be switched off before the display is
removed. However, nothing will be damaged if
you attach or detach the display while the drive
system is switched on.
Wait for about 30 seconds after removing the
display before switching the display back on
again; otherwise, successful system initialisation
cannot be guaranteed.
1Turn the display 90° anticlockwise on its
mounting plate.
The electrical connections are disconnected.
2Remove the display.
The drive system will switch off about
10 seconds after the display is detached. If the
light was on, it will also switch off after about
15 seconds.
6.14.3 Using the main beam
The drive system needs to be switched on first to
turn on the main beam.
Press main beam button briefly.
The main beam is switched on and the main
beam symbol is displayed on the main beam
button.
Press the main beam button briefly again.
The main beam is switched off and the main
beam symbol is displayed.
6.14.4 Selecting the level of assistance
Press the plus button.
The level of assistance is increased.
Press the minus button.
The level of assistance is reduced.
The set level of assistance is shown on the
display.
6.14.5 Switching on recovery
Recovery can only be activated within a speed
range between 6 and 45 km/h. Recovery cannot
be activated when the vehicle is stationary or
travelling at under 6 km/h.
The battery cell temperature must be higher than
0 °C to switch on recovery. Recovery is
automatically deactivated under 0 °C.
The battery charge level must be higher than 10%
to switch on recovery. The lower the battery level
is, the harder braking is due to recovery.
Press the minus button repeatedly until you
reach level of assistance 0.
Use the minus button to switch down one level
further from this level.
Recovery will work at a low power output at
level 1.
Use the minus button to switch down one level
further.
Recovery will work at a high power output at
level 2.
6.14.6 Switching off recovery
Press the Plus button repeatedly until you
reach level of assistance 0.
Recovery is now switched off.
Notice
Do not use the display as a handle. The
display may become irreparably damaged if
you use it to lift the S pedelec.
Remove the display from its mount if the
S pedelec is not going to be used for several
weeks. Store away safely in a dry environment
at room temperature.
47


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kettler Velossi 2.0 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kettler Velossi 2.0 in the language / languages: English as an attachment in your email.

The manual is 7.33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kettler Velossi 2.0

Kettler Velossi 2.0 User Manual - German - 83 pages

Kettler Velossi 2.0 User Manual - Dutch - 82 pages

Kettler Velossi 2.0 User Manual - French - 84 pages

Kettler Velossi 2.0 User Manual - Spanish - 85 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info