683161
107
Zoom out
Zoom in
Previous page
1/196
Next page
Adjusting VOX Delay Time
During transmission of audio or data using the VOX function, the
transceiver may sometimes be restored to the receiving state, and
the end of the audio that is clipped off may not be transmitted as
a result. To prevent this from occurring, the delay time can be
adjusted to insert an appropriate pause before switching from the
transmitting to the receiving state.
1 Press and hold [VOX] to display the VOX
configuration screen.
2
Press F2 [ ]/ F3 [ ] to select the audio source
input (horizontal row).
Select the audio source input row to adjust from “MIC”, “ACC
2”, “USB” and “LAN”.
3
Press F4 [ ]/ F5 [ ] to select the “VOX DELAY”.
4 Press F6 [–]/ F7 [+] or turn the [MULTI/CH] control
to select the delay time.
Input signal from the audio source selected in step 2, and adjust
the delay time before returning to the receiving state after audio
input has ended.
Setting Value
0 to 10 (default) to 20 (1 step)
When “MIC” is selected, adjust the delay time while
speaking into the microphone.
The delay time for “MIC” can also be adjusted by turning the
[DELAY] control.
5 Press and hold [VOX] or press [ESC] to end the
process.
VOX Voice Delay
When the VOX function is ON, there may be a time lag before
transmission begins after voice input has started. For this reason,
the beginning part of the audio may be clipped off. To prevent this
phenomenon from occurring wherever possible, a VOX voice
delay time can be configured between the timing when
transmission is activated and before audio signals are sent out.
When using a microphone as the audio source input
for transmission:
Configure in Menu [6-13] VOX Voice Delay
(Microphone)
When using devices other than a microphone as the
audio source input for transmission:
Configure in Menu [6-14] VOX Voice Delay (Except
Microphone)
Setting Value Off/ Short/ Middle (default)/ Long
TX Monitor
TX audio can be monitored while transmission is in progress. This
is a convenient tool for checking the effect of the speech processor
or TX equalizer. In the FSK and PSK modes, FSK and PSK signals
transmitted by this transceiver can be monitored.
Press [MONI] to turn the TX monitor ON or OFF
The [MONI] LED lights up in green when the TX monitor is
turned on.
The ON/OFF status of the TX monitor and monitor level are
stored in the memory for each of the mode groups below.
During split operation, the mode at the transmitting end will
be monitored.
SSB/ FM/ AM
SSB-DATA/ FM-DATA/ AM-DATA
FSK/ PSK
Each time there is a change in the mode, the transceiver
switches back to the TX monitor ON/OFF status stored in
each group. TX monitor is always OFF in the CW mode.
Adjusting the TX Monitor Level
The volume level when monitoring the TX audio can be adjusted.
1 Press and hold [MONI] to display the TX Monitor
Level configuration screen.
.
2 Press F4 [–]/ F5 [+] or turn the [MULTI/CH] control
to select the TX monitor level.
Setting Value 0 to 10 (default) to 20 (1 step)
3 Press and hold [MONI] or press [ESC] to end the
process.
Feedback may occur when a speaker is used in the SSB,
AM or FM mode. Make use of a headphone instead.
Transmission of CW messages cannot be monitored
using the TX monitor. To monitor CW messages, make
use of CW sidetone.
In the FM, FSK and PSK modes, the audio of the TX
monitor may differ from the audio of the signal that is
actually transmitted.
TRANSMIT FUNCTIONS 8
8-3
107


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-890S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-890S in the language / languages: English as an attachment in your email.

The manual is 21,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TS-890S

Kenwood TS-890S User Manual - German - 196 pages

Kenwood TS-890S User Manual - Dutch - 196 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info