683161
19
Zoom out
Zoom in
Previous page
1/196
Next page
.
ACC 2 Connector
Pin No. Pin Name Function Input/Output
NC No connection
2 RTTY RTTY control terminal (FSK key input) I
3 ANO
Audio output
Connect to the audio input of a PC or an external device such as a PC connection interface.
The audio output level is independent of the AF volume control knob on the front panel.
The audio output level can be adjusted in Menu [7-09]. Adjust it to an appropriate level.
When the audio output level is configured to the default value of “50” in Menu [7-09], the peak-to-
peak voltage is approximately 0.5 V p-p in the case of standard modulation signals. Altering the
audio output level between “0” and “100” changes the peak-to-peak voltage level between
approximately 0 Vp-p and 1.2 Vp-p. (Impedance 10 kΩ)
O
4 GND Signal ground
5 PSQ
Squelch control output
Connect to the squelch input of an external device such as a PC connection interface.
When squelch is open: Low impedance
When squelch is closed: High impedance
O
6 MET 1 Meter level output 1 O
7 NC No connection
8 GND Signal ground
9 PKS
PTT input for data communication (DATA SEND)
Connect to the PTT output of an external device such as a PC connection interface.
Signal can be transmitted by connecting the PKS terminal to GND.
The PKS terminal mutes unnecessary modulation input signals during transmission.
Refer to Configuration of the Input Path of TX Audio (8-1).
I
10 MET2 Meter level output 2 O
11 ANI
Audio input for data communication
Connect to the audio output of a PC or an external device such as a PC connection interface.
The audio input level is independent of MIC GAIN on the front panel.
The audio input level can be adjusted in Menu [7-07].
Standard modulation can be obtained with an input of approximately 10 mVrms in the default
setting of “50” in Menu [7-09]. Altering the audio input level between “0” and “100” changes the
standard modulation input level between approximately almost no modulation and approx. 1
mVrms. (Impedance 10 kΩ)
I
12 GND Signal ground
13 SS
PTT input
This is the same terminal as pin 2 (SS terminal) of the MIC connector on the front panel and pin 3
(SS terminal) of the REMOTE connector.
It has the same behavior as pressing [SEND] on the front panel.
Signal can be transmitted by connecting the SS terminal to GND.
The SS terminal mutes unnecessary modulation input signals during transmission.
Refer to Configuration of the Input Path of TX Audio (8-1).
I
INSTALLATION AND CONNECTION 1
1-7
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-890S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-890S in the language / languages: English as an attachment in your email.

The manual is 21,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TS-890S

Kenwood TS-890S User Manual - German - 196 pages

Kenwood TS-890S User Manual - Dutch - 196 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info