683161
17
Zoom out
Zoom in
Previous page
1/196
Next page
Configuration for Switching the RX Bandwidth
Configure the setting as follows to switch the RX bandwidth by cutting off the high or low frequencies within the frequency range of 0 Hz
to 5000 Hz even in the SSB-DATA mode, in the same way as in SSB mode, during operations such as FT8.
* Refer to “Configuring the Behavior of the HI/SHIFT and LO/WIDTH Controls (SSB/SSB-DATA Only)” (6-3).
Configure in Menu [6-12] Filter Control in SSB-DATA Mode (High/Low and Shift/Width). Select “High & Low Cut”.
USB cable and RS-232C straight cable are not supplied with this transceiver. Please purchase commercially available cables.
Delays may occur when using USB audio, and there may also be audio interruptions depending on the performance and load
of the PC.
Place this transceiver far enough from the PC so that noise will not be picked up.
For data communication software settings, refer to the instruction manual or Help file of the software in use.
Virtual COM Port
PC command control using the virtual COM port and USB keying control using the RTS/DTR signal of the virtual COM port can be
performed by connecting this transceiver and the PC using a USB cable.
To use the virtual COM port, Windows 10, Windows 8.1 or Windows 7 is required. (as of January, 2019)
Install the virtual COM port driver on the PC before connecting the USB cable. Download the driver from the following URL.
http://www.kenwood.com/i/products/info/amateur/software_download.html
There are 2 types of virtual COM port on this transceiver, namely virtual COM (Standard) port and virtual COM (Enhanced) port.
The COM port numbers of the virtual COM (Standard) port and virtual COM (Enhanced) port on the PC can be checked using the
following way.
Open the Device Manager in Windows.
Connect this transceiver and the PC using a USB cable. The following 2 COM ports are displayed in “Ports (COM & LPT)” in the
Device Manager.
Silicon Labs CP210x USB to UART Bridge (COM x)
Silicon Labs CP210x USB to UART Bridge (COM y)
x and y are numbers. The numbers vary depending on the PC environment used. The following is the display example of the virtual
COM ports on this transceiver assigned to COM3 and COM4.
.
Double-click on these in the Device Manager to display the respective Properties windows.
Select the “Details” tab and then select “Location paths” from the Property drop-down menu.
Move the mouse cursor to the top line displayed in the “Value” column and check the number in the parenthesis on the right end
of the character string.
The port displayed with the number (1) is the virtual COM (Standard) port of this transceiver.
The port displayed with the number (2) is the virtual COM (Enhanced) port of this transceiver.
The following is the display example of the Properties window of each COM port when the virtual COM (Standard) port and the virtual
COM (Enhanced) port are assigned to COM3 and COM4 respectively.
.
INSTALLATION AND CONNECTION 1
1-5
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-890S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-890S in the language / languages: English as an attachment in your email.

The manual is 21,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TS-890S

Kenwood TS-890S User Manual - German - 196 pages

Kenwood TS-890S User Manual - Dutch - 196 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info