606693
66
Zoom out
Zoom in
Previous page
1/104
Next page
60
Scan is a useful feature for hands-off monitoring of your
favorite frequencies. After becoming comfortable with
how to use all types of Scan, the monitoring flexibility
gained will increase your operating efficiency.
This transceiver provides the following types of Scan:
PROGRAM SCAN
The Program Scan function scans the range between
the Start frequency and End frequency stored in
memory channel 99. If Program Scan is used before
you store a Start and an End frequency, then the lower
and upper frequency limits of the transceiver are
automatically stored for the Start and End frequencies
respectively. Some General market versions substitute
the lower and upper frequencies for the current band in
place of the frequency limits of the transceiver.
Program Scan direction is controlled by the Start and
End frequency relationship. The following table
summarizes the way that Program Scan functions:
SCAN
For a refresher on how to store the Program Scan
Limits, refer to “STORING SCAN LIMITS IN CH 99”
{page 58}. The following are additional important points
regarding the Program Scan function:
Starting a transmission by closing the CW key, by
sending a packet, or by triggering the VOX circuit by
voice or the DRU-3 Digital Recording Unit stops
Program Scan; however, transmission does not
begin immediately.
When the Program Scan range is smaller than a
single step of the M.CH/VFO.CH control, turning this
control causes Scan to jump to the lower of the
Start/End frequencies, then continue scanning.
Starting the Program Scan function switches OFF
the RIT and XIT functions. RIT and XIT are not
switched ON again when Program Scan stops, and
the RIT/XIT offset frequency is not cleared.
•Operating mode can be changed while scanning.
If Automatic Mode is switched ON, it will function
with the Program Scan function.
Use the following procedure to activate Program Scan.
1 Select the VFO mode using VFO A or VFO B.
2 Press [SCAN].
3 To stop scanning, press [SCAN], or [CLR], or
[SEND], or Mic [PTT].
SCAN HOLD
While using Program Scan, if Menu No. 65
(PG.S.HOLD) is switched ON, then turning the Tuning
or M.CH/VFO.CH control stops the transceiver from
scanning for approximately five seconds. This is also
true if Mic [UP] or [DWN] is pressed. Program Scan
resumes after the five second pause. The default is
OFF.
CONFIRMING START/END LIMITS
1 Recall memory channel 99.
2 Press [DOWN] to check the Start frequency and
press [UP] to check the End frequency.
Jumps to Start
frequency
End Relationship
Start frequency
LOWER THAN
End frequency
Start frequency
EQUAL TO
End frequency
Start frequency
HIGHER THAN
End frequency
Within Scan
range
Lower or higher
than Scan range
Start/End
frequency
Lower or higher
than Start/End
frequency
Within Scan
range
Lower or higher
than Scan range
Up
Jumps to Start
frequency, then
scans up.
Monitors
Start/End
frequency.
Jumps to
Start/End
frequency and
monitors it.
Down
Jumps to Start
frequency, then
scans down.
Start/End
Frequency
Relationship
Current
Frequency
Program Scan
Action
General update of activity
on the entire band or a
sub-section of the band
while in VFO mode.
Quick activity update of all
programmed Conventional
memory channels.
Quick activity update of a
selected group of
Conventional memory
channels.
All-channel
Scan
Group Scan
Memory
Scan
Program Scan
Scan Type Purpose
66


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-870S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-870S in the language / languages: English as an attachment in your email.

The manual is 2,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TS-870S

Kenwood TS-870S User Manual - Dutch - 102 pages

Kenwood TS-870S User Manual - French - 102 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info