606693
28
Zoom out
Zoom in
Previous page
1/104
Next page
22
FRONT PANEL METER
The multifunction meter measures the parameters in the
following table. Peak readings for the S-meter, ALC,
SWR, COMP, and PWR functions are held for
approximately 2.5 seconds if Menu No. 09 (P HOLD) is
ON.
Pressing the [METER] button cycles through the
functions as shown below:
Receive Mode:
Note:
While receiving, the scales for the S-meter and the receive
pass band function are always visible.
Transmit Mode:
Note:
While transmitting, the transmit power meter is always visible.
The COMP meter functions only when the Speech Processor is
ON in SSB or AM mode.
4 OPERATING BASICS
S
RX
FILTER
PWR
ALC
SWR
COMP
Received signal strength
Width and shift of the
receive pass band
Transmit output power
Automatic level control
status
Antenna system
standing wave ratio
Speech compression
when using the Speech
Processor
Receive
Receive;
or Transmit plus
[METER] ON
Transmit
Transmit plus
[METER] ON
Transmit plus
[METER] ON
Transmit plus
SSB/AM plus
[PROC] ON plus
[METER] ON
Displays
Scale
Functional
Condition
Receive
pass band
SWR \
ALC
d
c
b
COMP
Note:
After recalling memory channel 99 that has Start and End
frequencies stored {page 58}, the receive frequency can be changed
(like a VFO) by using the
Tuning
control.
DIRECT FREQUENCY ENTRY
Entering a frequency directly from the numeric keypad
can be the fastest method to change to a specific
frequency that is far removed from your current
frequency.
The following points will help you enter a frequency
correctly:
•Only the digits 0, 1, 2, or 3 can be entered for the
10 MHz digit (first digit). Pressing any digit 4 ~ 9 will
cause the digit to be entered in the 1 MHz position.
Therefore, to select a frequency of 3 MHz or lower,
enter 0 for the 10 MHz digit.
When the 10 Hz digit (last digit) is entered, the digit 0
is entered automatically for the 1 Hz digit, and
frequency entry is completed. The 1 Hz digit is not
displayed.
If [ENTER] is pressed after beginning to enter digits,
0 is entered automatically for the remaining
un-entered digits, and frequency entry is completed.
Attempting to enter a frequency that is outside the
TS-870S frequency range causes an alarm to be
generated. The entered frequency is rejected.
If an incorrect digit is pressed, restore the previous
frequency by pressing [CLEAR], or [SEND], or
Mic [PTT].
When an entered frequency is accepted, RIT
{page 44} and XIT {page 45} are switched OFF, but
the RIT or XIT frequency is not changed.
<<< (9L) >>>
1 Press [ENTER].
“– – . – – – . – –” appears.
2 Press the numeric buttons [0] ~ [9] to enter the
frequency you desire.
The transceiver changes to the entered
frequency after the 10 Hz digit is pressed.
Note:
After recalling memory channel 99 that has Start and End
frequencies stored {page 58}, the receive frequency can be changed
by using Direct Frequency Entry. When using the keypad to directly
enter a frequency, you can never enter a frequency outside the
frequency range programmed in memory channel 99.
50
49
38
27
16
OFF
CAR DELAY
AGC KEY SPEED
METER PROC MONI
0
2
46
8
100
2
46
8
10
MIC
ATT
ANT DOWN UP
VOX FULL/SEMI
AT TUNE
SEND
THRU/AUTO
AIP
PHONES
PROC MONI
MIC PWR
M.IN
REC F.LOCK
CH 4 CLR
CH 3 SCAN
CH 2 M>VFO
CH 1 M.IN
ENTER TF-SET
FINE
1MHz
QUICK MEMO
MR
SLOW FAST
0
2
46
8
10
SWR
PWR
S
9
7
5
3
1
1
0
2
5
50
FILTER
A
L
C
3
10 2
1
.5
1
0
2
0
4
0
10
0
6
0
W
d
B
d
B
2
0
COMP
M.CH
USB CW R FSK FM AMLSBAUTO
FULLVOX SEMI AIP AGC AUTO PROC MONI
HF TRANSCEIVER TS-870
ON AIR AT TUNE
50
49
38
27
16
REC F.LOCK
CH 4 CLR
CH 3 SCAN
CH 2 M>VFO
CH 1 M.IN
ENTER
USB
AGC AUTO
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-870S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-870S in the language / languages: English as an attachment in your email.

The manual is 2,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TS-870S

Kenwood TS-870S User Manual - Dutch - 102 pages

Kenwood TS-870S User Manual - French - 102 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info