606692
90
Zoom out
Zoom in
Previous page
1/96
Next page
82
15 TROUBLESHOOTING
Problem Probable Cause Corrective Action Page
VOX does not
operate.
The VOX gain is set too low. Increase the VOX gain. 32
HF/ 50 MHz Linear
amplifi er does not
operate.
1 The linear amplifi er control
is OFF.
2 The REMOTE connector
wiring is wrong or faulty.
1 Set Menu No. 59 (HF) or 60 (50 MHz) to 1, 2,
, 3, 4, or 5.
2 Inspect the REMOTE connector wiring and
correct it as necessary.
55
70
The transceiver’s
output power
decreases after a
short operating time.
1 The air fi lters for the cooling
fans have been congested
with dust.
2 The cooling fans cannot
provide enough air fl ow to
cool the transceiver down.
1 Contact a KENWOOD authorized service
center to clean the fi lters.
2 Relocate the transceiver so that air can easily
ow through the TS-590SG to keep the unit
cooled.
You cannot access
and use repeaters.
1 Many repeaters require a
subtone or 1750 Hz tone to
access.
2 Transmission and/or
reception frequency is
wrong.
1 Review “FM REPEATER OPERATION” and
select the correct frequency and type of
subtone.
2 You must transmit on the repeater’s input
frequency and receive on the repeater’s
output frequency. Refer to “FM REPEATER
OPERATION”.
25
25
Digital operation
results in few or no
connects or contacts
with other stations.
1 Physical connections
between the transceiver,
computer, and TNC/ MCP
are incorrect, or software
settings in the TNC/ MCP
are wrong.
2 Different transmission and
reception frequencies are
being used.
3 The levels between the
transceiver and the TNC/
MCP are incorrect.
4 Your transmitted signal or
the incoming receive signal
is too weak.
5 The TX delay time
parameter in your TNC/
MCP was incorrectly set.
1 Re-check all connections using this manual,
your TNC/ MCP manual, and your computer
hardware manual as references.
2 Confi rm that the RIT and XIT functions are
switched OFF. Confi rm that you are not
operating split frequency.
3 Adjust TX and RX levels using Menu Nos. 73
and 74, and level controls on your TNC/ MCP.
4 Reorient/ relocate your antenna or increase
your antenna gain.
5 Set the TNC/ MCP TX delay time to more
than 300 ms.
72
30,32
61,72
1
Attempts at controlling
the transceiver with
the computer have
failed.
1 Problem with cable that
connects the PC to the
TS-590SG.
2 Communication parameters
set in your terminal
program do not match the
transceiver parameters.
1 Check the cable and cable connections.
2 Use the same parameters in the terminal and
the transceiver. Check Menu Nos. 67 and 68.
71
60
“TEMP-HI” appears
and “CHECK” in
Morse code sounds.
A sensor in the transceiver
detected high temperature.
Stop transmitting and let the transceiver cool
down for a while. Contact a KENWOOD
authorized service center to clean the internal air
lters.
Transmission
suddenly stops.
The voltage of the DC power
supply is too high.
Adjust the DC power supply voltage to
13.8 V DC.
1
“DSP ERR x” appears
(where x is a number
from 0 ~ 3).
An internal DSP error occurs. Restart the transceiver by turning the power
OFF and then back ON. If the problem persists,
consult KENWOOD authorized Service Center.
“VGS ERR” appears. An internal error occurred in
the VGS-1.
Confi rm that the connector of the VGS-1 is
securely connected to the transceiver, then
turn the transceiver power OFF and ON. If
the problem persists, contact a KENWOOD
authorized service center for repairs.
76
90


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-590SG at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-590SG in the language / languages: English as an attachment in your email.

The manual is 4,99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TS-590SG

Kenwood TS-590SG User Manual - German - 96 pages

Kenwood TS-590SG User Manual - Dutch - 96 pages

Kenwood TS-590SG User Manual - French - 96 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info