Manual Kenwood TS-480SAT (page 65 of 104) (English)

511243

Zoom out

Zoom in

1/104

12 SCAN

VGROUP–9). As you select the Memory Channel,

“on” or “oFF” appears on the main frequency

display. “on” signifies that the memory channel is

active for the Program Scan and “oFF” signifies

that the memory channel group is inactive for the

Program Scan.

4 To activate the Program Scan frequency range,

select the desired VGROUP number by turning the

MULTI control. Then, press [ ] to select “on” for

the VGROUP (channel). When a channel is

activated for the Program Scan, “on” appears on

the display.

Note:

At least one of the valid Program Scan channels (from 90 to

99) must be programmed and selected to perform the Program Scan.

If no VGROUP (memory channel 90 ~ 99) is selected for the Program

Scan, the transceiver performs the VFO Scan {above}.

5 Press [SCAN/ SG.SEL] or [MTR/ CLR] to return

to the current VFO mode.

6 Press [SCAN/ SG.SEL] to start the Program

Scan.

•To quickly move towards a desired frequency

while scanning, turn the Tuning control or the

MULTI control, or press Mic [UP]/ [DWN].

•Turning the RIT/ XIT control clockwise

decreases the scan speed and

counterclockwise increases the speed, except

while in FM mode. The current scan speed is

shown on the display; P1 is the fastest speed

and P9 is the slowest.

• While in FM mode, Scan automatically stops

on a frequency where a signal is present. The

transceiver will either remain on that channel

for a short time (Time-Operated mode) or until

the signal drops out (Carrier-Operated mode),

depending on which mode you select via Menu

No. 11 {page 58}.

7 To stop Scan, press [SCAN/ SG.SEL] or

[MTR/ CLR].

Note:

◆

If you have turned the

SQL

control clockwise, far beyond the

squelch threshold while in FM mode, Scan may fail to stop at a

channel where a signal is present. If this happens, turn the

SQL

control slightly counterclockwise.

◆

If you press

[SCAN/ SG.SEL]

before storing any frequency range

for memory channels 90 to 99, the transceiver starts VFO scan.

◆

When the current receive frequency is within one of the ranges

that you selected with channel numbers, Scan starts with the

current frequency. The operating mode stored in the memory

channel is used.

◆

The operating mode can be changed while scanning, but the

memory channel is overwritten with the changed mode.

◆

When the current Scan range is smaller than a single step of the

MULTI

control, turning the control clockwise causes Scan to jump

to the start frequency, and counterclockwise to the end

frequency.

◆

Starting Program Scan switches OFF the RIT

and XIT functions.

◆

While in FM mode, the Program Scan monitors rounded off

frequencies regardless of the Menu No. 05 setting.

PROGRAM SCAN PARTIALLY SLOWED

You can specify a maximum of 5 frequency points for

each memory channel from 90 to 99 so that the

Program Scan slows down the scanning speed. To

specify the slow down frequency points, first program

the start and end frequencies into a memory channel

(90 ~ 99) {page 53}.

1 Access Menu No. 08 to confirm that the function is

ON (default is ON).

2 You can further configure the slow down frequency

width. Access Menu No. 09 to select the range

from 100 Hz to 500 Hz (default is 300 Hz).

Note:

If you select, for example, 500 Hz for Menu No. 09, the

Program Scan slows down to a

500 Hz width, centering the

frequency you marked below.

3 Press [A/B / M/V] (1 s) and turn the MULTI control

to recall the memory channel (90 ~ 99) for which

you want to specify the scan slow down

frequencies.

4 Press [ ]/ [ ] to confirm the start ([ ]) or end

([ ]) frequency.

5 Turn the Tuning control to the center frequency

point that you want the Program Scan to slow

down. Press [QMI/ M.IN] to mark the slow down

frequency point. The “ ” icon appears.

6 Repeat step 5 to specify the center slow down

frequency points. You can specify a maximum of

5 frequency points for each channel.

7 If you want to clear a slow down frequency point

that you previously stored, select the frequency

that you stored. Press [QMI/ M.IN] at this

frequency spot where “ ” appears.

•A confirmation beep sounds and the

transceiver “ ” disappears.

• If you want to clear all the slow down frequency

points at once, perform the Channel \

Channel Transfer to overwrite the memory data

to the same memory channel {page 52}. This

operation removes all the frequency points that

you stored.

8 Press [A/B / M/V] to return to VFO mode.

9 Press [SCAN/ SG.SEL] to start the Program Scan

with the slow down frequency point(s).

Note:

◆

During the Program Scan, you can turn the

RIT/ XIT

control to

adjust the scanning speed. Turn the control clockwise/ counter-

clockwise to slow down/ speed up the scan. The Program Scan

speed indicator appears on the main dot-matrix display during

the Program Scan; P1 is the fastest speed and P9 is the slowest.

◆

You cannot change the Program Scan speed in FM mode.

◆

You can specify the Program Scan slow down frequency point in

FM mode but it does not function.

SCAN HOLD

This function stops Program Scan for approximately

5 seconds, then resumes Scan when you jump to the

desired frequency by turning the Tuning control or the

MULTI control, or by pressing Mic [UP]/ [DWN].

To use this function, access Menu No. 10, and select

“on”. The default is OFF.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-480SAT in the language / languages: English as an attachment in your email.

The manual is 6,73 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TS-480SAT

Kenwood TS-480SAT User Manual - German - 104 pages

Kenwood TS-480SAT User Manual - Dutch - 104 pages

Kenwood TS-480SAT User Manual - French - 104 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Kenwood TS-480SAT Manual

Product: