45743
58
Zoom out
Zoom in
Previous page
1/150
Next page
50
11 SPECIALIZED COMMUNICATIONS
PREPARATION
1 Connect the transceiver to your personal
computer (via an external TNC or MCP if desired).
See “COMPUTER” {page 93} and “MCP AND
TNC” {page 95}.
2 Install an appropriate terminal program onto the
personal computer.
A variety of freeware and shareware programs
can be obtained in various ways. Consult your
reference material or other “packeteers”.
3 Initiate the terminal program and set the following
parameters on the personal computer:
Transfer rate (TNC/MCP <–> Computer):
9600 bps (default setting)
Data length: 8 bit
Stop bit: 1 bit
Parity: Non-parity
Flow control: Hardware
4 Press [A/B] to select VFO A or VFO B.
5 Access Menu No. 46 and select the main band or
the sub-band (default) as the data band.
“TNC” appears on the data band.
If you are using an external TNC or MCP,
access Menu No. 50E to make this selection.
The default is main band.
6 Access Menu No. 47 and select 1200 bps (default)
or 9600 bps as the transfer rate between TNCs.
You must select the same transfer rate as the
target station.
If you are using an external TNC or MCP,
access Menu No. 50F to make this selection.
The default is 1200 bps.
7 Select an operating frequency.
8 Press [LSB/ USB/ AUTO] or [FM/ AM/ NAR] to
select LSB, USB, or FM mode.
9 Access Menu No. 50A and select ON to activate
the DSP packet filter for the main transceiver.
10 Turn the HI/ SHIFT control to select the center
frequency of the packet mode. You can further
select either “NAR” (narrow) or “WID” (wide) for
the receiver filter width by turning the LO/ WIDTH
control.
ycneuqerFretneC edoMgnitarepO
zH000113KSP
zH0071)spb0021KSFA(tekcaP
zH0122)spb003KSFA(tekcaP
KSPKSP
Note:
The packet (9600 bps) operation is not affected by the DSP
packet filter settings.
The DSP packet filter works only on the main transceiver.
If you are using an external TNC or MCP, proceed
with the subsequent steps.
11 Following the instructions provided with your TNC
or MCP, enter the calibration mode so that you
can generate a mark condition.
The MAIN band LED changes from green (RX)
to red (TX).
12 Access Menu No. 50B to select the appropriate AF
input level.
Select a proper input level, so that the ALC
meter reflects within the ALC zone.
13 Exit the calibration mode.
The MAIN band LED changes from red (TX) to
green (RX).
14 Access Menu No. 50C to select the appropriate
AF output level.
You cannot use the AF control to make this
adjustment.
If you have selected sub-band in step 5,
access Menu No. 50D instead.
The frequencies (measured in kHz) commonly used
for Packet are listed below:
adanaC/.A.S.U )acirfA/eporuE(1noigeRURA
0381~0081—
5363~02630063~0953
0017~0807—
05101~04101—
5.99041~5904121141~10141,99041~98041
01181~50181—
00112~0901202112~00112
98182~0218200392~00292,05182~02182
08705~00605—
090541~019441—
570144~579044520134~050034
DCD SENSE
You can also select the method for inhibiting the built-
in TNC from transmitting. Access Menu No. 48 and
select one of the two methods. The default is “TNC
BAND”.
TNC BAND:
The TNC does not transmit when signals are present
on the TNC (data) band.
MAIN&SUB:
The TNC does not transmit when signals are present
on the main transceiver or sub-receiver.
58


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-2000E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-2000E in the language / languages: English as an attachment in your email.

The manual is 2,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info