Manual Kenwood TS-2000E (page 54 of 150) (English)

45743

Zoom out

Zoom in

1/150

10 SUB-RECEIVER

The “ ” and “ ” icons are both on the sub-

receiver display:

• You can do all the above, plus transmit on the

SUB band frequency.

This transceiver provides many other methods for

selecting a frequency quickly. For further details, refer

to “SELECTING YOUR FREQUENCY” {page 37}.

SUB-RECEIVER PANEL METER

The multifunction meter measures the parameters

described in the table below. The S-meter appears

when in receive mode and the PWR meter appears

when in transmit mode. Peak readings for the

S- meter and PWR functions are held momentarily.

elacS yalpsiD etatSnoitcnuF

ShtgnertslangisdevieceRevieceR

RWPrewoptuptuotimsnarTtimsnarT

Note: Peak Hold readings cannot be deactivated.

SELECTING A MODE FOR THE SUB-RECEIVER

First, confirm that the “ ” icon is on the SUB band

display. If it is not, press [SUB] or [CTRL] to assign

the function controls to the SUB band.

The SUB band can only be used to transmit in FM

mode and receive in FM or AM mode. Press

[FM/ AM/ NAR] to toggle the operating mode for the

sub- receiver. The narrow bandwidth operation for

AM is not available for the SUB band frequency.

Refer to “NARROW BANDWIDTH FOR FM”

{page 29} for FM operation.

FM CTCSS OPERATION

You can assign an independent CTCSS tone to the

sub-receiver. Refer to “FM CTCSS OPERATION”

{page 35} for function and control details.

FM DCS OPERATION

You can assign an independent DCS code to the sub-

receiver. Refer to “FM DCS OPERATION” {page 36}

for function and control details.

TONE FREQ. ID SCAN

This function scans through all the tone frequencies

in order to identify the incoming tone frequency on

the receiving signal of the sub-receiver. Refer to

“TONE FREQ. ID SCAN” {page 34} for function and

control details.

DCS CODE ID SCAN

This function scans through all the DCS codes in

order to identify the incoming DCS code on the

receiving signal of sub-receiver. Refer to “DCS

CODE ID SCAN” {page 36} for function and control

details.

• Holding down the key changes the bands

continuously.

• If “MHz” is visible on the display, first press

[1MHz/ SEL] to exit from the 1 MHz Step Up/

Down mode.

ADJUSTING THE AUDIO FREQUENCY (AF) GAIN

Turn the SUB AF control clockwise to increase the

audio level and counterclockwise to decrease the

level.

SUB

CALL

C.IN

SUB

1MHz

CTRL

TF-

SET

MAIN SUB

SG.SEL

SCAN

RIT

CW TUNE

9.6k STA

RIT/SUB

CON

XIT

ALT

SET

CLEAR

P.C . T

HF/VHE/UHF ALL MODE MULTI BANDER TS-2000

SQL

Note: The position of the SUB AF control does not affect the volume

of beeps caused by pressing buttons. The audio level for Packet

operation is also independent of the SUB AF control setting.

ADJUSTING THE SQUELCH

Turn the SUB SQL control clockwise when no signals

are present, to select the squelch level at which

background noise is just eliminated. The SUB band

LED turns off when the squelch is ON.

SELECTING A FREQUENCY

When you operate both the main transceiver and the

sub-receiver at the same time, you will be in one of

the following conditions. First, check where the “ ”

and “ ” icons are on the display, then follow the

instructions below.

The “ ” and “ ” icons are both on the MAIN band

display:

• Turn the RIT/ SUB control to adjust the sub-

receiver frequency.

“ ” is on the SUB band display and “ ” is on the

MAIN band display:

• Turn the RIT/ SUB control to adjust the sub-

receiver frequency.

“ ” is on the MAIN band display and “ ” is on the

SUB band display:

• Turn the RIT/ SUB control, the MULTI/ CH control,

or the Tuning control to adjust the frequency. Or,

directly enter the frequency using the numeric

keypad {page 37}. However, the input frequency

must be within the sub-receiver frequency range.

The frequency you selected may round up to the

nearest workable frequency step size {page 37}.

You cannot transmit on the sub-band frequency.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-2000E in the language / languages: English as an attachment in your email.

The manual is 2,89 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Kenwood TS-2000E Manual

Product: