45743
44
Zoom out
Zoom in
Previous page
1/150
Next page
36
8 ENHANCED COMMUNICATIONS
FM DCS OPERATION
Digital Code Squelch (DCS) is another FM application
which allows you to ignore (not hear) unwanted calls.
It functions the same way as CTCSS. The only
differences are the encode/ decode method and the
number of selectable codes. For DCS, you can select
from 104 different codes listed in the table below.
1 Press [A/B] to select VFO A or VFO B.
•“tA” or “tB” appears to show which VFO is
selected.
2 Select a band.
3 Select an operating frequency.
4 Press [FM/ AM/ NAR] to select FM mode.
“FM” appears.
5 Turn the SQL control to adjust the squelch.
6 Press [•/ DCS/SEL] to switch the DCS function
ON (or OFF).
“DCS” appears when the function is ON.
7 Press [FUNC], [•/ DCS/SEL].
The current DCS code appears. The default is
023.
8 Turn the MULTI/ CH control to select the
appropriate DCS code.
The available DCS codes are listed in the
following table.
320560231502552133314564216137
520170431212162233324664426237
620270341322362343134305726437
130370541522562643234605136347
230470251622662153544615236457
630411551342172653644325456
340511651442472463254625266
740611261542603563454235466
150221561642113173554645307
350521271152513114264565217
450131471252523214464606327
9 Press [FUNC], [•/ DCS/SEL] again to complete
the setting.
You will hear calls only when the selected code is
received. To answer the call, press [SEND] or press
and hold Mic [PTT], then speak into the microphone.
Skip steps 7 to 9 if you have already programmed the
appropriate DCS code.
Note: You cannot use DCS with the Tone or CTCSS functions.
DCS CODE ID SCAN
This function scans through all DCS codes to identify
the incoming DCS code on a received signal. You
may find this useful when you cannot recall the DCS
code that the other persons in your group are using.
1 Press [FUNC], [•/ DCS/SEL].
The current DCS code appears.
2 Press [SCAN/ SG.SEL] to activate the DCS Code
ID scan.
“DCS” blinks and every DCS code is scanned.
When the DCS code is identified, the
transceiver stops scanning and the identified
DCS ID is displayed.
Press [SCAN/ SG.SEL] to resume scanning.
Press [SCAN/ SG.SEL] to stop scanning while
the DCS code ID scan is active.
Note: Received signals are audible while scanning is in progress.
44


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-2000E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-2000E in the language / languages: English as an attachment in your email.

The manual is 2,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info