45743
42
Zoom out
Zoom in
Previous page
1/150
Next page
34
8 ENHANCED COMMUNICATIONS
AUTOMATIC REPEATER OFFSET
This function automatically selects an offset direction,
according to the frequency that you select on the
144 MHz band. The transceiver is programmed for
offset directions as shown below. To obtain an up-to-
date band plan for repeater offset direction, contact
your national Amateur Radio association.
Access Menu No. 43 and switch the function ON or
OFF. The default is ON.
K-type (U.S.A. and Canada versions)
This complies with the standard ARRL band plan.
All E-types (European versions)
Note:
Automatic Repeater Offset does not function when Reverse is
ON. However, pressing [TF-SET] after Automatic Repeater
Offset has selected an offset (split) status, exchanges the receive
and transmit frequencies.
If you change the offset direction by pressing
[0/ SHIFT/OFFSET] when Automatic Repeater Offset is ON, the
Shift direction on the above figure is applied when you change
the frequencies.
REVERSE FUNCTION
After programming an offset on the 29, 50, 144,
430/ 440 MHz, and 1.2 GHz (Optional) band, the
reverse function exchanges a separate receive and
transmit frequency. So, while using a repeater, you
can manually check the strength of a signal that you
receive directly from the other station. If the station’s
signal is strong, both stations should move to a
simplex frequency to free up the repeater.
Press [TF-SET] to switch the Reverse function ON
(or OFF) while the Shift function is active.
“R” appears when the Reverse function is ON.
Note:
If you press [TF-SET] and try to receive outside the available
receive frequency, the transceiver will not allow you to tune the
frequency. The Reverse function will not operate.
Automatic Repeater Offset does not function while Reverse is
ON.
You cannot switch Reverse ON or OFF while transmitting.
AUTOMATIC SIMPLEX CHECK (ASC)
ASC functions only when you have programmed an
offset on the 29, 50, 144, 430/ 440 MHz or 1.2 GHz
(Optional) band. While using a repeater, ASC
periodically monitors the strength of a signal that you
receive directly from the other station. If the station’s
signal is strong enough to allow direct contact without
a repeater, the ASC indicator on the display starts to
blink.
Press and hold [TF-SET] for approximately 1 second
to switch the function ON.
The “[R]” indicator appears when the function is
ON.
When direct contact is possible, the “[R]” indicator
blinks.
To quit the function, press [TF-SET].
Note:
Pressing Mic [PTT] causes the ASC indicator to stop blinking.
ASC does not function if your transmit and receive frequencies
are the same (simplex operation).
ASC does not function while scanning.
Activating ASC while using Reverse switches Reverse OFF.
If you recall a memory channel or the Call channel that has the
Reverse status ON, ASC is switched OFF.
ASC causes received audio to be momentarily intermitted every
3 seconds.
TONE FREQ. ID SCAN
This function scans through all tone frequencies to
identify the incoming tone frequency on a received
signal. You can use this function to find which tone
frequency is required by your local repeater.
1 Press [FUNC], [4/ TONE/SEL].
The current tone frequency appears.
2 Press [SCAN/ SG.SEL] to activate the Tone
Freq. ID.
“T” blinks and every Tone frequency is
scanned. When the Tone frequency is
identified, the transceiver stops scanning and
the identified frequency is displayed.
Press [SCAN/ SG.SEL] again to resume
scanning.
Press [SCAN/ SG.SEL] to stop scanning while
the Tone frequency ID scan is active.
+
+
S
S
SS
144.0 145.5 146.4 147.0 147.6
145.1 146.0 146.6 147.4 148.0 MHz
S: Simplex
S
S
S: Simplex
144.0
146.0 MHz145.8145.6
42


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-2000E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-2000E in the language / languages: English as an attachment in your email.

The manual is 2,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info