45743
22
Zoom out
Zoom in
Previous page
1/150
Next page
14
4 GETTING ACQUAINTED
DISPLAY
F
I
L
T
E
R
S
1
3
5
7
9
2
0
4
0
6
0
d
B
P
W
R
1
0
2
5
5
0
1
0
0
W
%
A
L
C
61
2 4
10
93 5
11 13 15
7
8
12 14 16
q METER
While receiving, serves as an S-meter to measure
and display the received signal strength. It also
displays the filter width. While transmitting, serves as
a power meter plus an ALC meter, an SWR meter, or
a Speech Processor compression meter. The Peak
Hold function holds each reading for approximately
half a second.
Note: SWR meter works only for the HF and 50 MHz bands.
w
Appears while the internal antenna tuner {page 72} or
an external antenna tuner is in-line for the HF/ 50 MHz
band reception.
e AT
Appears while the internal antenna tuner {page 72} or
an external antenna tuner is in-line for the HF/ 50 MHz
band transmission.
r
Appears while HF RX ANT {page 76} connector is
enabled to receive HF band signals. You cannot
transmit the signals though this connector.
t
Either “ ” or “ ” appears, depending on
whether the Antenna 1 connector or the Antenna 2
connector is selected for the HF/ 50 MHz band
{page 72}.
y MHz
Appears when the MHz Up/ Down mode using the
MULTI/ CH control is switched ON {page 37}.
u ALT
Appears when ALT (Auto Lock Tuning) is activated for
the 1.2 GHz (FM) band {page 72}.
i
Appears while Memory Recall or Memory Scroll is
being used {page 59}.
o
Shows the memory channel number for the main
transceiver. If you select a channel over 99, a
leading digit (1 or 2) appears (the memory number
ranges from 00 to 299). It also shows the Quick
Memory number location (the Quick Memory number
ranges from “0_” to “9_”).
!0 AUTO
Appears when Auto mode selection is activated
{page 73}.
!1
Appears when the main transceiver is selected for the
transmission band.
!2
Appears when the main transceivers functions can
be controlled using the front panel keys.
!3 ATT
Appears when the main transceivers receiver
attenuator (approx. 12 dB) is ON {pages 57, 73}.
!4 TNC
Appears when the internal TNC is assigned to the
main transceiver {page 49}.
!5 PRE
Appears when the receiver pre-amplifier of the main
transceiver is ON {page 57}.
!6 + =
“+” or “–” appears, indicating which offset direction is
selected for the main transceiver. “=” appears when
the –7.6 MHz (430 MHz) or –6.0 MHz (1.2 GHz)
offset is selected (all E-types only) {page 32}.
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-2000E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-2000E in the language / languages: English as an attachment in your email.

The manual is 2,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info