45743
21
Zoom out
Zoom in
Previous page
1/150
Next page
13
4 GETTING ACQUAINTED
REAR PANEL
EXT. SP2
8
PANELCOM
ANT 2 ANT 1
ANT
144
AT
ANT 1.2G
DC
13.8V
ANT
430
EXT. SP1
8
ACC2
EXT. CONT
REMOTE
HF
RX ANT
PADDLE
KEY
GND
2 1
1
9
10 12 13 14 1511
32 4 5 86
7
q ANT 1 and ANT 2 connectors
Connect your primary HF/ 50 MHz antenna to ANT 1. If
you are using 2 antennas for the HF/ 50 MHz band,
connect the secondary antenna to the ANT 2 connector.
w GND post
Connect a heavy gauge wire or copper strap between
the ground post and the nearest earth ground {page 1}.
e KEY and PADDLE jacks
The PADDLE jack mates with a 6.3 mm (1/4")
3-conductor plug for connecting a keyer paddle to the
internal electronic keyer. The KEY jack mates with a
3.5 mm (1/8") 2-conductor plug for connecting an
external key for CW operation. Read “Keys for CW
(PANEL and KEY)” {page 3} before using these jacks.
r AT connector
Mates with the connector on the cable supplied with
the external antenna tuner. Refer to the instruction
manual supplied with the tuner for more information.
t ANT 144
Connect your 144 MHz band antenna to this connector.
y ANT 430
Connect your 430/ 440 MHz band antenna to this
connector.
u ANT 1.2G (TS-2000/ TS-B2000 Optional)
Connect your 1.2 GHz band antenna to this connector.
i DC 13.8V power input connector
Connect a 13.8 V DC power source to this connector
{page 2}. Use the cable supplied with the regulated
DC power supply.
o COM connector
Mates with a 9-pin female RS-232C connector for
connecting a computer via one of its serial
communication ports {page 93}. Also used with the
Quick Data Transfer function {page 93}.
!0 PANEL connector
Connect a cable from the optional separate remote
panel (RC-2000) to this connector.
!1 EXT.SP1 and EXT.SP2 jacks
Mate with a 3.5 mm (1/8"), 2-conductor (mono) plugs
for connecting external speakers {pages 3, 78}.
!2 EXT.CONT connector
Connect your 50 MHz, 144 MHz, 430/ 440 MHz or
1.2 GHz linear amplifier control cable to this
connector {page 76}.
!3 ACC2 connector
Mates with a 13-pin male DIN connector for
connecting various accessory equipment, such as an
external TNC/ MCP or a RTTY terminal {page 94}.
!4 REMOTE connector
Mates with a 7-pin male DIN connector for connecting
an HF linear amplifier {page 76}. Do not connect
50 MHz, 144 MHz, 430/ 440 MHz, or 1.2 GHz linear
amplifier controls to this connector; use the
EXT.CONT connector instead.
!5 HF RX ANT connector
Connect a separate receive-only antenna for HF low
bands to this jack (RCA connector) {page 76}.
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-2000E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-2000E in the language / languages: English as an attachment in your email.

The manual is 2,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info