606707
69
Zoom out
Zoom in
Previous page
1/77
Next page
VGS-1 (OPTIONAL) OPERATION
When using the optional VGS-1 voice guide & storage unit, you gain access to the voice recorder and voice announcement functions.
VOICE ANNOUNCEMENTS
When changing modes, frequencies, settings, etc., an audio voice
will announce the new information.
Voice announcements are output from the PTT band side.
1 Enter Menu mode and access Menu 003.
2 Set the announcement function to MANUAL, AUTO, or OFF.
Refer to the tables below for announcements based on settings.
MANUAL:
A microphone PF key must be programmed as [VOICE] to
use MANUAL voice announcement.
Operation Announcement
While in VFO
mode
Press [VOICE]:
Operating band frequency
While in MR mode
Press [VOICE]:
“Channel” + Channel number +
operating band frequency
While in Call
mode
Press [VOICE]:
“Call channel” + operating band
frequency
While in Menu
mode
Press [VOICE]:
Menu number or setting value
(some selections have no voice
announcement)
Tone frequency
setup
Press [VOICE]:
“Tone frequency” + frequency value
CTCSS frequency
setup
Press [VOICE]:
“CTCSS frequency” + frequency value
DCS code setup
Press [VOICE]:
“DCS” + code value
Cross tone setup
“TX” + “TONE” or “DCS” + “RX” +
“TONE” or “CTCSS” or “DCS” or “OFF”
AUTO:
Announcements are made automatically when changing a
mode/frequency/setting.
Operation Announcement
Press [VFO] “VFO”
Press [MR] “MR”
Press [CALL] “Call”
Press [MENU] “Menu” + menu number
Press [F] “Function”
Press [PM] “PM”
Press [ENT] “Enter”
AUTO:
Announcements are made automatically when changing a
mode/frequency/setting.
Operation Announcement
Change the
operating band/
turn the power ON
“A”/“B” + “Channel” (for MR only) +
“Call”/channel number + “Channel”
(for CALL only) + operating band
frequency + output power level + (PM
channel number (OFF, 1~5) (turn the
power ON))
Change the
frequency band
New receive frequency
Setting up the PM PM Channel number/“PM OFF”
Frequency direct
entry
Entered key number
Memory Direct
Entry mode
Channel number
Press [F], rotate
Tuning control
On stored channel
“Memory in” + channel number +
frequency
Press [F], [M.IN] in
VFO mode
On blank channel
“Memory in” + channel number +
“Blank”
Press [A/B] in
VFO mode
“A”/“B” + frequency + output power
level
Press [F] and then
the Tuning control
in VFO mode
“Menu” + “Mode” + The main Menu
number corresponds to the fi rst digit.
(For example, “5” is Menu No. 5xx.)
Select Menu
number in
category
“Menu” + menu number
Select setting
value in Menu
mode
Setting value
Clearing a
memory channel
“Memory” + “Channel”+ channel
number + “Clear”
Perform a Full
Reset
“Full reset?”
Perform a Partial
Reset
“Partial reset?”
Perform a VFO
Reset
“VFO reset?”
Perform a PM
Reset
“PM reset?”
Press [LOCK]
(to turn the Lock
function ON)
“Lock on”
Press [LOCK]
(to turn the Lock
function OFF)
“Lock off
Tone frequency
setup
“Tone frequency” + frequency value
VGS-1
69


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TM-D710GA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TM-D710GA in the language / languages: English as an attachment in your email.

The manual is 7,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TM-D710GA

Kenwood TM-D710GA User Manual - English - 55 pages

Kenwood TM-D710GA User Manual - German - 74 pages

Kenwood TM-D710GA User Manual - Dutch - 75 pages

Kenwood TM-D710GA User Manual - Dutch - 55 pages

Kenwood TM-D710GA User Manual - French - 77 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info