511233
32
Zoom out
Zoom in
Previous page
1/64
Next page
27
7 SCAN
USING VISUAL SCAN (MEMORY CHANNEL)
1 Press [MR] to enter Memory Recall mode.
2 Turn the Tuning control or press [ ]/ [ ] to select
your desired center memory channel.
3 Press [F], [INFO] to start the Visual Scan.
The transceiver start scanning the 5 upper
memory channels and 5 lower memory
channels, by centering the selected memory
channel.
The current scanning memory channel number
and frequency are displayed on the current
operating band. On the other band, the relative
S-meter level of each frequency channel is
displayed.
To pause Scan, press and hold [MONI]. While
the Visual Scan is paused, the center
frequency bar-graph blinks and you can
monitor the frequency. Release [MONI] to
resume the Visual Scan.
4 To change the current scanning channel, turn the
Tuning control or press [ ]/ [ ].
5 To stop the Visual Scan, press [F], [INFO].
Note:
You can press [PTT] (or [CALL] if 1750 Hz is programmed) to
transmit during the scan if the center frequency is within the
transmission frequency range. The center bar-graph blinks while
transmitting.
If 11 or more memory channels are stored, “
s
” and “
t
” do not
appear.
Even if the Fine Tuning ON status is stored in the memory
channels, the Visual Scan (Memory Channel) starts.
MEMORY CHANNEL LOCKOUT
You can lock out memory channels that you prefer
not to monitor during Memory Scan.
1 Press [MR] to enter Memory Recall mode.
2 Turn the Tuning control or press [ ]/ [ ] to select
the memory channel to be locked out.
3 Press [F], [MHz].
•“” appears at the top right of the memory
channel number, indicating the channel is
locked out.
4 To unlock the memory channel, repeat steps 1 ~ 3.
•“” disappears.
Note:
The Program Scan memories (L0/U0 ~ L9/U9) and Priority
channels (Pr1 and Pr2) cannot be locked out.
Even if a memory channel is locked out, you can perform the Call
Scan {page 25} between the Call channel and memory channel.
If the same memory channel is recalled to the A and B-band, you
cannot lock out the channel.
SCAN RESUME METHOD
The transceiver stops scanning at the frequency (or
memory channel) where a signal is detected. It then
continues or stops scanning according to which
resume mode you have selected.
Time-Operated mode (default)
The transceiver remains on a busy frequency (or
memory channel) for approximately 5 seconds,
then continues to scan, even if the signal is still
present.
Carrier-Operated mode
The transceiver remains on the busy frequency (or
memory channel) until the signal drops out. There
is a 2-second delay between signal dropout and
scan resumption.
Seek mode
The transceiver moves to a frequency or memory
channel where a signal is present and stops.
To change the scan resume method:
1 Press [MNU].
2 Turn the Tuning control or press [ ]/ [ ] to select
Menu No. 1 (SCAN RESUME).
3 Press [ ] or [MNU].
4 Turn the Tuning control or press [ ]/ [ ] to select
“TIME ” (Time-Operated mode), “CARRIER”
(Carrier-Operated mode), or “SEEK” (Seek mode).
5 Press [ ] or [MNU] to store the setting.
Otherwise, press [ ] or [PTT] to cancel.
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TH-F7E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TH-F7E in the language / languages: English as an attachment in your email.

The manual is 1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TH-F7E

Kenwood TH-F7E User Manual - Dutch - 64 pages

Kenwood TH-F7E User Manual - French - 64 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info