617939
4
Zoom out
Zoom in
Previous page
1/14
Next page
lomm
íi)
,
i
Remove insulation
Speakers
This
unit has two
pairs
of speaker terminals, SPEAKERS A and
SPEAKERS B.
Connecting
one speakor systom
Connect
speakers rated at 4 ohms or more to the SPEAKERS
A terminals.
Connecting
two speaker systems
To
connect
an additional
pair
of speakers, use
the B ter-
minals. ln
this case. each speaker must be rated at 8 ohms or
more.
Gonnection
whh
speaker
cords
1 . Connect
the leÍt speaker to the
E
SPEAKERS terminals and
the right
speaker to the
El
SPEAKERS
terminals.
2. Be
careful that wires do not
contact adjacent
terminals.
3. Be
sure to
connect
the
(+
)
terminal
of
the speaker to the
(+
)
terminal
of
the unit.
Never
short the
(
+
)
and
(-
)
terminals.
Erroneous
connection of speakers may result
in
poor
imaging
or unnatural
sound.
Record
Plug the leÍt and right input cables the tape deck into the
E
and
E
fAPE 2 REC
jacks.
Second
tape deck
Plug the
input
and
output cables Írom the second tape
deck
into
the
REC
and
PLAY
jacks
marked TAPE 1.
VCR
(VIDEO/AUDIO) jacks
Two video
recorders
can be connected
to the VCR
A
and VCR
B
jacks.
Connect the unit's
VIDEO PLAY
jack
to the video
recorder's video output terminal, the
VIDEO
REC
jack
to the
video input terminal, the AUDIO PLAY
E
jack
to
the left
audio
output terminal, AUDIO PLAY
tr
jack
to
the
right
audio output
terminal, AUDIO REC
El
jack
to
the left audio
input
terminal, and
the AUDIO REC
tr
jack
to the
right
audio
input terminal.
(Video
recorder
with monaural audio should be connected
to one of the
VCR A
jacks.
After connecting it to the
E
or
B
AUDIO
jack
of the VCR A
jacks,
set the MONO/STEREO switch
to
"MONO".)
MONO/STEREO switch
This
switch affects
only the VCR A
jacks.
Set the switch
according
to
the stereo or
monaural
audio
output mode
of
the video recorder connected to the
VCR A
jacks.
MONITOR
OUT
iacks
Two video
monitors
can
be
connected
to the MONITOR
OUT A and
MONITOR
OUT
B
jacks. (The
video
monitors or TVs should be equipped
with
video
input
terminals.
)
Connect
the MONITOR OUT A
or
B
jaclito
the video in-
put
terminal of each
video monitor.
SYNCHRO
CONTROL
terminal
when
the KD-74F/KD-64F
(rurntable),
KX-74R
(tape
deck) or
DP-840
(CD
player)
are
used in connection
with the
receiver. they can be operated
from the
remote control unit of
the receiver
when their synchro
terminals are connected
to the SYNCHRO
CONTROL
terminals.
(Ordinary
audio cable connections
are also
required.) For details,
refer to the operating
instructions
for the remote control
unit on
page
'l
1.
@
:l-
from lead tip.
<s{-
Twist
wire tightly,
and solder.
press
the lever.
lnsert the wire and
return
the
leveÍ.
Speaker
lead
connection
The
wire
is
now locked.
Turntable
The PHONO
jacks
of the
unit can
accept
a
turntable
with
an
MM type
phono-cartridge.
Your
stereo
turntable has
a
pair
of audio cables that
is ter-
minated
with
phono plugs.
Plug
the left
channel
plug
into
the
E
and
the right
channel
plug
into the
B
PHONO
jacks.
lf the turntable
has a
ground
wire,
connect
it
to the
unit's
GND terminal
to avoid hum.
CD/AUX
To
these
jacks,
high-level
signal
sources such as,
CD
player,
tuner,
extra
tape decks, TV, VTR
sound outputs,
etc. can be
connected.
Ground
For
maximum
safety and minimum interference
connect the
GND terminal
to a
good
earth
ground
if
practicable.
A
good
earth
ground
is
a cold water
pipe
or
a
metal
stake driven into
moist earth.
However, never
use a
gas pipe
for this
purpose.
Tape
decks
lf only
one
tape deck is to
be connected to the
system
it is
recommended
that
it
be connected to the
jacks
marked
TAPE
2.
(lf
your
tape
deck is equippied with
a 3
head
system, the
simultaneous
monitoring
can be
possible.)
Tape
deck
input
and output cables
are
normally
terminated
with
phono
plugs.
Playback
Plug
the leÍt
and
right
output cables of the
tape
deck into
the
E
and
E
TAPE
2 PLAY
jacks.
4 rvn-azon
tet
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood KVR-A7O at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood KVR-A7O in the language / languages: English as an attachment in your email.

The manual is 18,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info