161383
4
Zoom out
Zoom in
Previous page
1/20
Next page
KTF-3010/KTF-2010 (En)
4
R
L
TUNER
SYSTEM CONTROL
ƒ
PHONES A SPEAKER B BASS TREBLE BALANCE
INPUT SELECTOR
MUTING LOUDNESS
ON OFF
POWER
ON/STANDBY
STEREO INTEGRATED AMPLIFIER KAF-3010R
MIN MAX
VOLUME CONTROL
MDTAPETUNERPHONOCD
SOURCE DIRECT
thermally reactive advanced instantaneous transistor TRAIT
|{ |{
LR
ANTENNA
GND
AM
FM 75
BA
SYSTEM
CONTROL
ƒ
OUTPUT
R
L
SL16 XS 8
SL16 XS 8
System connection
Connection of the Audio components/Connection of the system control cord
Make connections as shown below.
When connecting the related system components, refer also
to the instruction manuals of the related components.
Do not plug in the power lead until all connections are com-
pleted.
Pre-main amplifier
Audio cord
System control cord
To wall AC
outlet
1.Connect all cords firmly. If connections are loose, you may lose the sound or interconnectable system control operations may not work.
2.When plugging and unplugging connection cord, be sure to first remove the power cord from the AC outlet. Plugging / unplugging
connection cords without removal of the power cord can cause malfunctions or damage to the unit.
Malfunction of microcomputer
If operation is not possible or erroneous display ap-
pears even though all connections have been made
properly, rest the microcomputer referring to "In case
of difficulty". ^
Notes
Notes
KTF-3010 only
Connecting system control cords after connecting a Kenwood audio component system lets you take advantage of convenient system
control operations.
There are two Kenwood system control modes. Make connections according to the groups of terminal symbols shown below.
[SL16] Mode : for
terminals only
[XS8] Mode : lets you combine F, f, and ƒ terminals
This unit is compatible with both [SL16] and [XS8] modes. It comes from the factory set to the [SL16] mode. To switch to the [XS8] mode,
follow the instructions in “Switching from [SL16] to [XS8]”.
1. [SL16] equipment cannot be combined with [XR], [XS], and [XS8] equipment for system
operations. If your equipment consists of this kind of combination, please do not connect
any system control cords. Even without system control cords, normal operations can be
carried out without affecting performance.
2. If your amp or receiver does not have a system control terminal, do not connect any
system control cords to the system control terminals on the other components.
3. Do not connect system control cords to any components other than those specified by
Kenwood. It may cause a malfunction and damage your equipment.
4. Be sure the system control plugs are inserted all the way in to the system control termi-
nals.
Notes
Notes
Caution regarding placement
To maintain proper ventilation, be sure to leave a space around the
unit (from the largest outer dimensions including projections) equal
to, or greater than, shown below.
Left and right panels: 10 cm
Rear panel: 10 cm
No matter to which of the two terminals the con-
nection is made, the use method is the same.
The system control connection
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood ktf 3010 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood ktf 3010 in the language / languages: English as an attachment in your email.

The manual is 0,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info