683035
7
Zoom out
Zoom in
Previous page
1/25
Next page
How to Install
How to Install
Installation Procedure
Check that the vehicle is parked on a level
surface.
1. Attach the device to the mount
bracket. (accessory)
Insert the mount bracket into the bracket attach-
ment part of the device and attach it to the device.
Camera
lens side
Mount bracket
2. Determine where to mount the device.
Determine the mounting position in reference
to “Recommended installation position.
3. Clean the mounting surface and then
ax the device to the windshield.
Use a commercially available cleaning cloth or
the like to wipe off all dirt and grease on the
mounting surface. Peel off the release paper of
the double-sided tape on the mount bracket
and push the bracket against the windscreen
to affix it in place. Leave the device for 24 hours
before using it to enable the mounting
strength of the mount bracket to improve.
Release paper
4. Perform the cord wiring work.
Refer to “How to Wire” and perform the wiring
work.( P. 14)
5.
Adjust the device's mount angle, then
fasten it.
When adjusting the mount angle, check that the
camera's field of vision is parallel to a flat ground
surface and that the sky to ground ratio is equal.
There is a spirit level at [MENU] – [System
settings] – [Mouting support tools] – [Level].
(
P. 34)
Use it to help adjustment of the mount angle.
Adjust the angle so that the moving circle
is as close as possible to the center of the
screen.
Windshield
Rear-view mirror
The Adjust according to the vehicle”
adjustments must be made in order to use
the driving support functions. ( P. 17)
Do this in a flat place with a line-of-sight
distance of approximately 200 meters.
Recommended installation position
z
Install the device in a position where it will not block the front view of the driver (position where hidden
by the rear-view mirror).
z
Install the device so that it is within the wiping range of the wiper.
z
Mounting the device to the center of the windshield behind the rear-view mirror will facilitate optimal
video recording.
Clip
Windshield
Doublesided
tape
Inside
vehicle
Outside
vehicle
Power cord
* Fix the power cord in place with commercially available soft
tape or the like.
Rearview
mirror
Power cord
Ceramic
part
Front pillar cover
Soft tape*
Front pillar
Power cord
CAUTION
When passing the power cord through the front pillar or another part, observe the points below when
performing the wiring work.
z
Wire the power cord farther forward or farther rearward than the airbag so that it does not interfere with
the airbag.
z
In the case of a vehicle in which the front pillar cover is fixed in place with special clips or the like, the
clips may need to be replaced after you remove the front pillar cover. For how to remove the front pillar
cover, the availability of replacement parts and other information, contact the vehicle dealer.
z
Fix the power cord in place with commercially available soft tape or the like so that it does not interfere
with driving.
Recommended installation position
12 13
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood DRV-830 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood DRV-830 in the language / languages: English as an attachment in your email.

The manual is 12,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood DRV-830

Kenwood DRV-830 User Manual - German - 49 pages

Kenwood DRV-830 User Manual - Dutch - 52 pages

Kenwood DRV-830 User Manual - French - 52 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info