686409

Kemppi A7 TIG Orbital System 300 Manual

35
Zoom out
Zoom in
Previous page
1/61
Next page
35
A7 TIG Orbital System 300© Kemppi Oy 2016 1615
OPERATING MANUAL
Pass 1, level 1
Move the cursor and enter values with the control knob.
• Amps: current at each level (using pulsed current,
this is high pulse current).
• Wire: Filler Wire Feed Rate (in IPM or CM per
minute, function not available).
• RPM: Rotation Speed
• LP Amps: Low Pulse Amperage, shown as
percentage of high pulse current.
• HPT: High Pulse Time Period, in seconds.
• LPT: Low Pulse Time Period, in seconds.
• HP RPM: rotation speed on high current pulse
(shown only when RPM STEP is turned ON). Can
be set at any percentage from 0–99 of the low
pulse speed listed RPM.
• LP Wire: Wire Step Function, index of wire feed
with pulsed current (not available).
• Level Time: the time during which these
parameters will be active in seconds.
• Time Remaining: as the tube size is input,
selection of RPM automatically calculates Total
(weld) Time.
• Time Remaining: automatically calculated once
Level Time is entered.
• Total Time: total time for weld in seconds. Enter
values and press Next soft key to go to Level 2.
Automatic parameters carry down through levels.
You can copy parameters from one level to the next by
pressing Next. Be careful when changing parameters at
one specic level so as not to impact other levels.
Example: You wish to change the amperage originally
programmed in Level 4 of a one pass weld. However,
other parameter changes occur in a subsequent level,
such as level 5 or 6. If you make the change in amperage
in Level 4 and press Next, you will automatically copy all
of the Program Level 4 values into Level 5. Therefore, it is
necessary to note any other changes that are occurring
in subsequent levels within the pass before modifying
any parameter in that pass. Please note that this is only
true for Level parameters within any given pass. For a
multi‐pass weld, once you move to a subsequent pass,
the parameters will not be copied from the previous
pass.
Pass 1, level 2
Move the cursor, enter values with the control knob and
press Next; or if no change is necessary, press Next.
Pass 1, level 3 to nal level
Continue moving through the screens for each level and
change parameters as needed.
… 35 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kemppi A7 TIG Orbital System 300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kemppi A7 TIG Orbital System 300 in the language / languages: English as an attachment in your email.

The manual is 4,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info