686374

Kemppi A7 Robot Gun Mount T3 Manual

12
Zoom out
Zoom in
Previous page
1/21
Next page
12
Robot Gun Mount T3© Kemppi Oy 2016 1712
OPERATING MANUAL
11.3 Mounting the hose assembly on the
robot
This section describes how to mount the hose assembly
on the robot.
Serious injuries can be caused by parts articulating
rapidly. When cleaning with compressed air, wear suitable
protective clothing – in particular, safety goggles.
When replacing the liquid-cooled A7 MIG Gun 500-w
hose assemblies, make sure that any coolant residues are
removed from the robot mount.
• When replacing the liquid-cooled A7 MIG Gun
500-w hose assemblies, make sure that any
coolant residues are removed from the robot
mount.
• When mounting liquid-cooled A7 MIG Gun 500-
w hose assemblies, make sure that the water
nipples in the welding torch coupling for the A7
MIG Gun 500-w unit are inserted correctly into
the hose assembly adapter. Observe the forced
positioning.
• After mounting is complete, check for any leaks.
Before Robot Gun Mount T3 and the cable assembly can
be mounted, the robot must be placed in maintenance
position.
Figure 6: Mounting the hose assembly – Fanuc only
3
7
6
1
4
2
5
9
8 10
1. Pull-in tool
2. Robot mount
3. Lock ring
4. 2 covers
5. Robot
6. Hose assembly
7. Hose assembly connection
8. Complete welding torch coupling
9. Washer
10. Fastening screw
Proceed as follows:
1. Rotate the lock ring (3), and open the cover (4).
2. Unscrew the fastening screw (10) from the welding
torch coupling (8) until the screw head and the
washer (9) make contact.
3. Introduce the hose assembly (6) from behind,
through the robot (5).
4. Insert the pull-in tool (1) from the front, through
the robot mount (2) and the robot (5), and screw
it into the hose assembly connection (7) as far as it
will go.
Only if the hose assembly connection has been
correctly inserted can it be attached properly with the
fastening screw.
5. Position the hose assembly connection (7)
with the positioning pin and the groove of the
welding torch coupling (8).
6. Pull in the hose assembly connection (7) as far
as it will go, and secure it with a fastening screw
(10), with max. tightening torque M = 7.5 Nm.
Observe the forced positioning.
7. Unscrew the pull-in tool (1).
8. Slide in the corrugated hose on the hose
assembly (6) as far as it will go.
9. Close the cover (4), and tighten with the lock
ring (3). Refer to Figure 4 for the standard axis
positions.
10. Fasten the wire feeder (1) to the wire bracket
mount (3).
11. The position of the wire feed (1) is due to the
position of the robot (maintenance position).
Make sure that the hose assembly can still be
moved 20 mm upwards and downwards after
the wire feeder has been attached.
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kemppi A7 Robot Gun Mount T3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kemppi A7 Robot Gun Mount T3 in the language / languages: English as an attachment in your email.

The manual is 1,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info