686374

Kemppi A7 Robot Gun Mount T3 Manual

10
Zoom out
Zoom in
Previous page
1/21
Next page
10
Robot Gun Mount T3© Kemppi Oy 2016 1712
OPERATING MANUAL
Proceed as follows:
1. Mount the intermediate ange (6) on the robot
(5), using eight (M4) cylinder-head screws. Max.
tightening torque M = 3.5 Nm
2. Fasten the insulating ange (4) to the intermediate
ange (6), using four cylinder screws (3). Max.
tightening torque M = 6 Nm
Make sure that the cylindrical pin (7) is in the correct
position. It species the reference position in relation to the
robot.
3. Fasten the complete welding torch coupling (2) to
the insulating ange (4), using six cylinder screws
(8). Max. tightening torque M = 3.5 Nm.
4. Mount the insulating sleeve (9) and the lock ring (1)
on the complete welding torch coupling (2), and
secure with the retaining ring (10).
11. INSTALLING ROBOT GUN MOUNT T3
Risk of injury due to unexpected start-up
For the entire duration of maintenance, servicing, unmounting, and repair work,
the following instructions must be adhered to:
• Switch o the power supply.
• Cut o the compressed air supply.
• Pull the power plug.
Read the safety instructions in this manual and the separate safety instructions.
The system may only be installed by authorized personnel.
11.1 Fastening Robot Gun Mount T3 to the robot
This section describes how to fasten the robot mount to the robot.
The parts of the system are depicted in the gure below.
Figure 3: Fastening Robot Gun Mount T3 to the robot
3
7 6
1
4
2
5
9
8
10
1. Lock ring
2. Complete welding torch coupling
3. 4 cylinder screws, M5×50
4. Insulating ange
5. Robot
6. Intermediate ange
7. Cylindrical pin
8. 6 cylinder screws, M5×16
9. Insulating sleeve
10. Retaining ring
For fastening Robot Gun Mount T3 to the robot, a robot ange (2) is required. It must
correspond to the hole pattern of the robot mount (1) and of the robot.
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kemppi A7 Robot Gun Mount T3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kemppi A7 Robot Gun Mount T3 in the language / languages: English as an attachment in your email.

The manual is 1,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info