686368

Kemppi A7 MIG Power Source 450 Manual

44
Zoom out
Zoom in
Previous page
1/67
Next page
44
A7 MIG Welder© Kemppi Oy 2018 1824
OPERATING MANUAL
4.5.1 Voltage source, levels and safety
The touch sensor provides eight software selectable DC voltage levels (see Table 4.19,
“Voltage levels”). The voltage level can be congured in the web user interface or the
setup panel. See Subsection 4.5.5, “Selecting output voltage” for more information on
the voltage level setup.
All levels have limited continuous power supply to ensure human safety. The 200 V
supply drops down under the 113 V level when loaded by a 5.6 kΩ resistor which is the
nominal DC resistance of the human body. In some cases, voltage levels above 113 V can
still cause minor harm, such as pain, to a person. Use the gate door safety switch with
touch sensor levels above 110 V.
The welder system features an arc measurement function which is performed between
the welding plus and minus poles near the welding arc using specic cabling and a
measurement circuitry. The measurement system inuences touch sensing when
the welding wire is used as a touch tool and when the arc measurement cables are
connected. The measurement system does not inuence touch sensing when the gas
nozzle is used as the touch tool.
The touch sensing is inuenced when
• the arc measurement cable between the power source and the wire feeder
(included in the cable set) is connected, but the arc measurement clamp from
the wire feeder to the workpiece is disconnected.
• the clamp is also connected. This situation is more harmful because it causes
false touch detection at certain voltage levels.
The Table 4.19, “Voltage levels” describes all setups and their relative voltage levels. The
accuracy of all values in the table except the nominal voltage is ±5 %.
Table 4.19 Voltage levels
Nominal
voltage
Voltage
(gas nozzle)
Voltage
(welding wire)
Voltage
(welding wire +
arc cable on)
Voltage
(welding wire +
arc clamp on)
50 V 55 V 54 V 54 V 50 V
80 V 80 V 80 V 77 V 74 V
110 V 110 V 110 V 105 V 87 V
150 V 150 V 150 V 130 V 89 V*
160 V 160 V 160 V 130 V 89 V*
170 V 170 V 170 V 130 V 89 V*
180 V 180 V 180 V 130 V 89 V*
200 V 200 V 200 V 130 V 89 V*
*Values cause false detection on touch sensor.
The power source and the touch sensing circuitry are galvanically isolated from the
other systems in the robot interface unit.
… 44 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kemppi A7 MIG Power Source 450 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kemppi A7 MIG Power Source 450 in the language / languages: English as an attachment in your email.

The manual is 3,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info