686368

Kemppi A7 MIG Power Source 450 Manual

33
Zoom out
Zoom in
Previous page
1/67
Next page
33
A7 MIG Welder© Kemppi Oy 2018 1824
OPERATING MANUAL
Welding parameters and functions
Figure 4.10 Memory channel editing – Welding parameters and functions view
In the Welding parameters view you can, depending on the selected welding process,
• set the min, max and initial values for Wire feed speed.
• set the min, max and initial values for Fine tuning or Voltage.
• set the value for the Dynamics and Pulse current.
• set the value manually or from the curve for Double pulse amplitude and
Double pulse frequency.
In the Welding functions menu you can, depending on the selected welding process,
• select Wise functions on and o and set up their eectiveness.
• select Hot start option OFF, ALWAYS ON or USER SETS ON/OFF and set Hot
start level and Hot start time by using the sliders.
• select Crater ll option OFF, ALWAYS ON or USER SETS ON/OFF and set Crater
ll step level, Crater ll end level and Crater ll time by using the sliders.
• select Creep start option CURVE or SET VALUE and set Creep start level by
using the sliders.
• select Start power by using the slider.
• select Touch sense ignition option OFF or ON
Welding settings – Welding system
Figure 4.11 Welding system settings view
In the Welding system view you can modify all settings related to the behavior and
function of the welding system.
In the General settings menu you can
• turn Water cooling ON, OFF and AUTO by clicking on the buttons.
• adjust Welding cable length by using the slider bar.
• select Fine tuning calibration point by using the slider bar.
• select Arc voltage measurement ON and OFF by clicking on the button.
In the Wire feed settings menu you can
• select wire feeder option: WIRE FEEDER 1, WIRE FEEDER 2 or SELECT AT ROBOT.
• adjust Wire feed motor current warning level by using the slider bar.
• select Wire feed end step ON and OFF by using the buttons.
In the Gas settings menu you can
• select Pre gas time and Post gas time as a preset value from welding program
(CURVE) or a value selected with a slider (SET VALUE).
… 33 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kemppi A7 MIG Power Source 450 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kemppi A7 MIG Power Source 450 in the language / languages: English as an attachment in your email.

The manual is 3,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info