686376

Kemppi A3 MIG Power Source 400 Manual

27
Zoom out
Zoom in
Previous page
1/32
Next page
27
A3 MIG Welder© Kemppi Oy 2018 1826
OPERATING MANUAL
5.2 Error codes
Code Description Measures
2 UNDERVOLTAGE
Undervoltage in the mains supply (phase missing)
Check the fuses.
3 OVERVOLTAGE
Lengthy overvoltage in the mains supply.
4 OVERHEAT
The overheat detector of the power source has gone o during welding.
Welding has continued for too long without interruption or the ambient
temperature is too high.
Do not switch o the power source. Let the fans cool down the device.
101 NO WELDING PROGRAM
Internal program error. The selected synergic welding curve was not found in
the memory. The system memory card is detached or defective.
Switch o and restart the power source. Contact the maintenance service if the
error is not resolved.
131 FIELDBUS INIT FAILED
Failed to initialize the eldbus during start-up.
Restart the device. Contact the maintenance service if the error is not resolved.
132 ROBOT COMMUNICATION ERROR
Communication to the robot has been lost. The eldbus cable has been
broken or detached, or there is a robot failure or shutdown. Welding is
interrupted when a lost connection is detected.
Check the eldbus cable. If the robot has been shut down, turn the robot on.
Switch o and restart the power source.
133 SAFETY STOP
The safety stop signal is activated by a user. Welding is immediately
interrupted.
Identify the reason for the safety stop. Do not release the safety stop signal before
the cause has been identied and resolved.
146 COLLISION DETECTED
The collision sensor has been activated. The welding torch mounted on
the arm of a welding robot has collided with the welding piece or another
obstacle.
Reverse the robot arm until the torch no longer touches the obstacle. Check the
torch in case of damages.
154 WIRE FEED MOTOR OVERCURRENT
Current limit is exceeded while the wire feed motor is running, and the motor
is stopped. The wire feeder rolls are too tight, the wire spool is too tight, or
the wire is stuck.
Check and replace the consumables in the wire feeder unit and the torch.
202 CURVE NOT ACTIVATED
An activated memory channel has not been congured properly.
Specify a welding curve for the memory channel.
### OTHER ERROR CODES Switch o and restart the power source. Contact the maintenance service if the
error is not resolved.
… 27 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kemppi A3 MIG Power Source 400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kemppi A3 MIG Power Source 400 in the language / languages: English as an attachment in your email.

The manual is 6,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info