Manual Kelvinator KBM4300WB (page 4 of 16) (English)

478053

Zoom out

Zoom in

1/16

Installing your refrigerator

The appliance should arrive with the

front adjustable rollers wound down to

tilt the top of the refrigerator backwards

by about 10 -15mm from upright.

The stability foot should also be wound

fully up so it will not interfere with the

operation of the rollers (see diagram

in Step 3 below).

caution

 Therollersaredesignedforforwardorbackward

movementonly.Theyarenotcastors.Movingthe

refrigeratorsidewaysmaydamageyouroorand

the rollers.

1. Roll the refrigerator into its nal position.

2. The top of the refrigerator should be tilted back by

approximately 10 -15mm. This will allow the doors to

self-close providing a consistent door seal.

3. If the refrigerator is not tilted back, you can adjust the

two front rollers by turning the large, plastic roller nut

(see diagram below). This will increase the height of the

rollers. One turn of the nut will tilt the refrigerator back

approximately 10mm. If you have difculty turning the

roller nut you can have someone tilt the refrigerator back,

so that you have better access. Alternatively, you can

access the rollers from the side, using a at screwdriver

to help you turn the nut (see diagram below).

4. Check the alignment of the refrigerator to the

surrounding cupboards. The top of the refrigerator

should be level from side to side (see diagram below).

If you need to adjust the level, use the adjustable rollers

as discussed in Step 3.

Installing your new refrigerator

ClearancearoundyourSidebySiderefrigerator

Your Side by Side Refrigerator can be installed between

cupboards or xtures but you must allow for the following

spaces around the cabinet.

1. allow a minimum of 5mm clearance on both sides.

2. allow 10mm clearance at the back of the refrigerator.

3. allow a minimum of 10mm clearance above hinge covers.

4. allow a 250 or 350mm clearance on the hinge side of

the doors, if you place the refrigerator next to the wall.

This will make cleaning easier.

5. make sure that cupboards or xtures do not stick out

further than the refrigerator cabinet.

ClearancearoundyourTopandBottomMountrefrigerator

1. allow a minimum of 5mm clearance on both sides.

2. allow 10mm clearance at the back of the refrigerator.

3. allow a minimum of 10mm clearance above hinge covers.

4. If you do not have a cupboard with a rear gap, the

recommended clearance area on top increases from

50mm to 90mm.

5. When positioned in a corner area, spacing of at least

350mm on the hinge side will allow the doors to open

enough to enable the removal of bins and shelves.

Note: Doors on all models are designed to sit proud of

cabinetry (not ush). The refrigerator should be placed

against a wall and the gap between the rear of the

refrigerator and the wall should be no greater than 75mm.

90mm

50mm

30mm

Recommended

airspace

CABINET

DOOR

350mm

10-15mm

Fixed rear

rollers

Height adjustable

front rollers

Top of refrigerator

is level ie. horizontal

Adjust front rollers

for uneveness of floor

eg. wind this roller

down or up

Aligned to

cupboards

ie. even gap

4 Installing your new refrigerator Kelvinator Refrigeration

Stability foot

wound up

Large plastic

roller nut

10mm

5mm

Recommended

airspace

CABINET

DOORS

10mm

35mm

Freezer

Door

Fridge

Door

250mm

350mm

10mm

5mm

Recommended

airspace

CABINET

DOORS

10mm

35mm

Freezer

Door

Fridge

Door

250mm

350mm

Hi, help please, where does the wire rack go in the freezer, I have the 2 baskets in but for the life of me, can’t work out where the rack goes? ??
Thanks H ???? Submitted on 10-11-2021 at 19:32
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Kelvinator KBM4300WB in the language / languages: English as an attachment in your email.

The manual is 2,58 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Kelvinator KBM4300WB Manual

Product: