738045

Keiser M3i lite Indoor Group Cycle Manual

16
Zoom out
Zoom in
Previous page
1/24
Next page
M3i lite INDOOR GROUP CYCLE 16
BACKLIGHT SENSOR While the computer is awake, the backlight sensor automatically detects ambient light levels in the
room and turns on the backlight display when needed.
RPM (CADENCE) The RPM displays the revolutions per minute of the crank arm—also known in the cycling world as cadence—
and is roughly the speed at which the cyclist is pedaling.
POWER AND ENERGY The power output is displayed in Watts (currently generating) and Kilocalories (total value for the
workout). The computer toggles back and forth between Watts for eight seconds and Kilocalories for two seconds. The rated
accuracy for power between 30 and 160 RPM is ±5 Watts for power below 50 Watts, and ±10% for power above 50 Watts.
HEART RATE If there is no Heart Rate signal, a steady heart symbol and a zero will be displayed. If a user is wearing a Heart
Rate strap, once the computer locks onto the signal, the heart symbol will blink and display the heart rate.
Only POLAR® with coded GymLink heart rate sensors are compatible with Keiser M Series indoor cycles.
ELAPSED TIME The number shown reports the total workout time spent and will reset to zero after 60 seconds of inactivity
or if the computer is reset using the gear shifter.
GEAR Gears from 1 to 24 are displayed on the bottom left hand of the screen.
ODOMETER/TRIP DISTANCE When the computer is activated, the Odometer “ODO” will display the distance accrual of the
bike for the rst eight seconds. This feature is for service and maintenance purposes only. After approximately eight seconds
the Odometer “ODO” will disappear to display the Trip units for two seconds (“USA” = Miles, “EURO” = Kilometers), followed
by the Trip Distance for the remainder of the workout. Trip is a calculated distance value (at road run) based on power
production (Note: To change the Trip units, follow the instructions within the “Bluetooth® smart” procedure on page 18).
1
2
3
4
5
6
7
OVERVIEW
DISPLAY FEATURES
WORKOUT DATA
To view averages: RPM, Power, and Heart Rate, at any point in the workout, stop pedaling for three seconds. This will ash
your averages until you start pedaling again or until the computer goes to sleep after 60 seconds.
INTERVAL TRAINING
To initiate an interval, starting from a high gear drop the Resistance Lever to “GEAR 1” for 1/4 of a second and lift it up to a
higher gear immediately. “inL #” will display conrming the interval has started.
Repeat the above steps to end the interval (“inL End” will display) and the averages for that interval will blink.
Note: The averages displayed at the end of your workout when pedaling has stopped are inclusive of all pedaling times and
intervals that have taken place during your workout.
Bluetooth® smart ENABLED
The Bluetooth® smart enabled computer allows Bluetooth® smart Ready devices such as cellphones, tablets, and computers
to gather information about your workout. M3i lite compatible apps allow data to be stored to track progress over time and
make the data available to other tness applications. Classrooms are able to utilize real time performance tracking programs
which give the entire class an opportunity to see their performance compared with other participants in the class.
To receive and download workout information from your M3i lite, a Bike ID number is required, which identies your M3i lite
for individual or group Bluetooth discovery. The Bike ID number is viewable within the rst eight seconds (displayed as “bid”
and followed by any number 1 to 200, see Figure 13). To assign a Bike ID to your M3i lite, see “Bluetooth® smart” procedure on
page 18. Note: Bike ID set to “0” will not be discovered by Bluetooth devices.
COMPUTER DISPLAY
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Keiser M3i lite Indoor Group Cycle at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Keiser M3i lite Indoor Group Cycle in the language / languages: English as an attachment in your email.

The manual is 8,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info