771580
7
Zoom out
Zoom in
Previous page
1/23
Next page
Installation & Owner's Manual
4
50mm larger than
the dia. of unit
Max.22mm
Heat Pump
Water Heater
User
Water Inlet
Anode rod
Drainpipe
Barrel-drain
Expansion Tank for tank
(if required)
Upper
Condensate Outlet
Lower
Condensate Outlet
Notice:
The temperature limiting
valve is required on the
hot water usage terminal.
PTR valve
Water Outlet Temp. Limiting
Valve
Tap Water
One Way Valve
Shut-off Valve
Anode rod
3. INSTALLATION
The circulating air for every unit should be more than 350m3/h. Make sure there is enough installation space. Outline dimensional drawing (see
Fig.2-3,Fig.2-4).
3.1 Water System Piping
Fig.3-1
Water inlet or outlet pipes: The spec of the water inlet or outlet thread
is RC3/4” (external thread). Pipes must be heat-insulated well.
1) Installation of the pipe for PTR valve: The spec of the valve
connecting thread is RC3/4” (internal thread). After installation, it
must be conrmed that the drainpipe outlet is exposed in the air.
CAUTION
Piping water system as the above gure. In case of installing
it at a place where outside temperature below freezing point,
insulation must be provided for all hydraulic components.
The handle of PTR valve should be pulled
out once per half a year to make sure that
there is no jam of the valve.
Please beware of burn, beware of the hot
water from the valve.
The drainage pipe should be well insulated
in order to prevent water inside pipe from
freezing in cold weather.
WARNING
Do not dismantle the PTR valve.
Do not block off the drainage pipe.
It will cause explosion and injury, if do not
comply with the above instruction.
2) Installation of the One Way Valve: The spec of the One Way Valve
thread in accessories is RC3/4”. It is used to prevent water from
owing backwards.
3) After water system piping work, turn on the cold water inlet valve
and hot water outlet valve and start effusing the tank. When water
ow smoothly out from water outlet pipe(tap water outlet), the tank
is full, turn off all valves and check pipeline to make sure there is
not any leakage.
4) If the inlet water pressure is less than 0.15MPa, a pump should be
installed at the water inlet.
For guarantee the safety usage of tank at the condition of water
supply pressure higher than 0.65MPa, a reducing valve should be
installed at the water inlet pipe.
5) Condensate may be leaked from unit if drainage pipe is blocked
or unit operates in high humidity environment, a drainage pan is
recommanded as shown as following gure:
Fig.3-2
EXPLOSION
Handle
Drainage
pipe
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kaysun COMPAK KHP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kaysun COMPAK KHP in the language / languages: English as an attachment in your email.

The manual is 2.84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info