550946

Kawasaki W 650 Manual

392
Zoom out
Zoom in
Previous page
1/433
Next page
15-72 ELECTRICAL SYSTEM
Switches an d Sensors
If the voltage is out of standard, adjust the sensor position
(see Throttle Sensor Position Adjustment).
If the voltage is within the standard, perform the following
inspection:
•
Stop the engine.
•
Measure the sensor’s output voltage at wide open throttle
with the ignition switch turned ON.
Throttle Sensor Output Voltage (wide open throttle)
Standard:
4.06 ∼ 4.26 V
If the voltage is out of standard, replace the throttle sen-
sor.
Throttle Sensor Position Adjustment
•
Connect the throttle sensor setting adapter between the
sensor wire connectors (see Throttle Sensor Inspection).
Special Tool - Throttle Sensor Setting Adapter: 57001
-1400
•
Start the engine.
•
Operate the engine at idle speed (see Periodic Mainte-
nance chapter).
•
Loosen the sensor mounting screws [A].
•
Adjust the sensor mounting position to set the sensor
output voltage to the standard, and tighten the mounting
screws.
Throttle Sensor Output Voltage (at idle)
Standard:
0.9 ∼ 1.1 V
If the standard voltage cannot be obtained, replace the
throttle sensor.
Oil Pressure Warning Light Delay Unit Inspection
•
Remove the lead [B] from the oil pressure warning light
switch [A], and ground it to the engine.
•
Turn the ignition switch [C] ON.
After the oil pressure warning light [D] illuminates, return
the oil pressure warning light switch lead to its o riginal
position.
If the oil pressure warning light does not illuminate, in-
spect the warning light bulb and wiring.
If there is no problem with the warning light bulb and
wiring, replace the oil pressure warning light delay unit
[E].
•
Turn the ignition switch ON.
•
Grounding the oil pressure warning light switch lead to
the engine should cause the oil pressure warning light to
illuminate after a delay.
•
Measure the length of time it takes the warning light to
illuminate after the switch lead has been grounded.
Illumination Lag Time
Standard:
Approx. 3 seconds
If the illumination lag time is considerably different from
the standard, replace the delay unit.
… 392 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kawasaki W 650 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kawasaki W 650 in the language / languages: English as an attachment in your email.

The manual is 9,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info