631745
6
Zoom out
Zoom in
Previous page
1/16
Next page
Note: During the initialisation of the channel unit, an
indicator on the top-right side flashes for a few
seconds:
In case of a faulty entry, the flashing continues.
Possible faults:
Wrong entry of the input frequency or symbol rate.
General fault of the reception system.
935.2155/D/0705/2.4e
Setting instructions
Adjustment of the DVB channel unit is carried out via the
control unit of UFG 308 or UFG 312. Required software
version of the control unit: UFO 385: at least 6.20
UFO 387: at least 6.40.
For adjustment, it is necessary to connect the channel
unit with the control unit. The keys mentioned below are
on the control unit. (For explanations regarding their
functions, refer to the instructions valid for the base units
UFG 308, UFG 312, UFG 316).
The parameter to be set is selected with the keys „“ or
“. The selected parameter flashes.
After all parameters have been set,save the setting by
pressing„M“ inthe
EEPROM
ofthe channelunit.
1. Selecting the input frequency
The input frequency is selectable between 950 MHz and
2150 MHz in MHz steps with the keys „+“ or „-“.
Inp. 2004 MHz
22,000 MS/s 5/6
Outp. S21 306.00 MHz
6,111 MS/s 64 QAM
Changing the input frequency by numeric character entry
is also possible:
1. Press the keys „“ and „“ at the same time.
2. Use the key „“ to select the desired digit.
3. Change the frequency with the keys „+“ or „-“.
4. Return to standard operation by pressing the keys
“ and „“ at the same time.
The symbol rate can be adjusted in 0.1 MS/s steps with
the keys „+“ or „-“.
Partly changing the input symbol rate in 0.001 MS/s
steps is also possible (Refer in this connection to Sect.
1/Sub-section 1-4).
The code rate (second line of the display; figure value e.
g. 5/6) and the output symbol rate (fourth line of the
display) are automatically determined.
If the fourth line of the display does not show the output
symbol rate but indicates „zu hoch“ (too high) or „zu
niedrig“ (too low), it is necessary to change the QAM
stages (see Sect. 4, selection of the QAM stages).
**** UFO 385 ****
SNR = 15.2 dB
< back to: sup-menu >
Inp. 2004 MHz *
22.000 MS/s
Outp. S21 306.00 MHz
-.— MS/s 64 QAM
2. Selecting the input symbol rate
Inp. 2004 MHz
22,000 MS/s
Outp. S21 306.00 MHz
6,111 MS/s 64 QAM
After the parameter „input frequency“ has been selected
and the button was pressed, the signal-to-noise-ra-
tio „SNR“ is shown in the sub-menu.
For the SNR display it is required that the channel unit
accepts the input signal (the indicator stops flashing).
In order to ensure trouble-free operation, the SNR should
be 7 dB
Back to the sub-menu with key .
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kathrein UFO 387 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kathrein UFO 387 in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 1,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info