629516
58
Zoom out
Zoom in
Previous page
1/80
Next page
Installation Menu
58
UFO
®
mini
In a “subscriber controlled processing system”, the input frequency of
the receiver is a xed setting. The “subscriber controlled processing
system” transmits the signals at this frequency. The reception
parameters for programme selection are communicated to the
receiving system by a DiSEqC™ command and set.
The setting that has to be selected depends on the design of the
“subscriber controlled processing system”.
Remote Frequency
If you have set the “UFO
®
mini
menu option to “On”, use this menu
mini menu option to “On”, use this menu mini
option to make the setting from the transmission frequency.
For the transmission frequency to be set, refer to the installation
manual for the “subscriber controlled processing system”.
It
is essential that you follow the instructions in the
subscriber
controlled processing system
installation manual.
UFO
®
micro
The setting for this menu option is also designed for operation of the
receiver in a processing system.
The return path of the coaxial cable is used for control and
communication between the receiver and the Kathrein UFO
®
The return path of the coaxial cable is used for control and
®
The return path of the coaxial cable is used for control and
micro
system. If the receiver is operated in a UFO
®
micro
receiving system,
the “UFO
®
system. If the receiver is operated in a UFO
®
system. If the receiver is operated in a UFO
micro
” menu option must be set to “On”.
The receiving system then assigns the receiver a special address upon
installation, so that it will recognise the control commands sent by the
receiver to the receiving system for signal selection.
In this operating mode, a remote frequency need not be set, as it is
specifi ed by the UFO
®
In this operating mode, a remote frequency need not be set, as it is
®
In this operating mode, a remote frequency need not be set, as it is
micro
system with the addressing.
If the receiver is being used in a UFO
®
micro
receiving system for the
rst time, the address previously assigned must be deleted. This is
done in the “UFO
®
rst time, the address previously assigned must be deleted. This is
®
rst time, the address previously assigned must be deleted. This is
micro
menu option by selecting “Reset” using the

done in the “UFO

done in the “UFO
and
keys. The receiver is then assigned the original factory
setting. It then needs to be set to “On” again. The receiver receives its
new address from the new system.
Default setting: “Off”.
Reset
does
not delete the
pre-programming.
Factory Settings
This item allows all parameters to be reset to the factory settings using
the
key. The factory settings do not necessarily correspond to the
settings required for your specifi c system.
After resetting, you may need to make all settings again.
58


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kathrein UFD 170 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kathrein UFD 170 in the language / languages: English as an attachment in your email.

The manual is 5,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info